BeamMed Sunlight Omnisense 7000S User Manual Download Page 9 | Manualshive

Page: 9 / 284

background image

ix

END USER LICENSE AGREEMENT

The Distributor shall be entitled to provide separate and additional warranty
terms respecting the Product, but shall not be authorized to bind

BeamMed

to

such additional terms and shall indemnify

BeamMed

against any such liability.

The Distributor’s standard End User License Agreement will include the fol-
lowing provisions:

1.

Purchase of the Product shall entitle the End User to a personal,
non-transferable, non-assignable, non-exclusive and limited rights
to use the software component of the Product

(the "

License

", and

the "

Software

" respectively).

2.

The Product is licensed as a single product. The End User may not

separate its component parts for use as more than one system or
for any other purpose.

3.

Protection of Intellectual Property.

(a)The Product is protected under national and international copyright,

trademark and trade secrecy law. The Product or components
thereof may be protected under national and international patent
laws. All right, title, and interest to the Software shall remain with
the Distributor and its supplier and/or licensor. The License granted
herein does not constitute a sale of the Software or any portion or
copy of it. A copy of the Software is provided to the End User only
to allow the End User to exercise its rights under the License. The
Hardware component of the Product is purchased by and the Soft-
ware is licensed to the End User for the End User's internal use and
the Product may not be used by, sub-licensed, re-sold, rented, or
distributed to any other party. The End User may not assign the End
User's rights under this Agreement without the prior written con-
sent of the Distributor.

«
...
7
8
9
10
11
...
»

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

Brand: NORLUX Pages: 2

Brand: Wavetek Pages: 74

Brand: Fairchild Pages: 16

Brand: Ultimaker Pages: 38

Brand: A&D Pages: 2

Brand: A&D Pages: 176

Brand: Bartscher Pages: 28

Brand: Bartscher Pages: 13

Brand: IBEX Pages: 10

Brand: M-system Pages: 12

Brand: Cameo Pages: 64

Brand: Cameo Pages: 100

Brand: CAME Pages: 32

STOMAMED COL-160

Brand: Orliman Pages: 12

Brand: ACS Pages: 28

Brand: Zafferano Pages: 28

Brand: Basler Pages: 33

Brand: Elma Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands