manualshive.com logo in svg

BeamMed Sunlight Omnisense 7000S, User Manual

The BeamMed Sunlight Omnisense 7000S is a revolutionary diagnostic device used for bone health assessment. Ensure proper usage and maintenance of this cutting-edge tool with our comprehensive User Manual. Download it for free from our website manualshive.com and unlock the full potential of this remarkable product.

Share
Download
background image

13-2

     User Guide     

CHAPTER 13

Troubleshooting

Measurement does 
not start (indicators 
remain red)

Verify that you are using the cor-
rect probe, and that the 

Start

 

button (or foot-pedal) has been 
pressed.
Verify that sufficient ultrasound 
coupling gel has been applied, 
and to the correct area. Check 
that the probe is in good contact 
with the patient’s skin.
Validate the system by executing 
the System Quality Verification 
procedure.
Check that the probe is properly 
connected and the connector 
screws tightened.
Abort and restart the measure-
ment if necessary.

The Acoustic Contact 
Indicator shows 
green but the Acous-
tic Signal Acquisition 
Indicator remains red

Validate the system by executing 
the System Quality Verification 
procedure.
Check that the probe is properly 
positioned for the specific site 
being measured.
If the patient’s soft tissue is 
extremely thick at the site, mea-
surement may be obstructed. In 
particular, patients with a Body 
Mass Index (BMI) greater than 
35 may exhibit this problem. In 
this case additional pressure to 
bring the probe closer to the 
bone may solve the problem.

Result of System 
Quality Verification is 
outside phantom 
range

Call Sunlight Customer Support

Problem

Possible Solution

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

GE Ettan IPGphor 3 Instrument User Manual preview
Ettan IPGphor 3
Brand: GE Pages: 64
GE AMX 4+ Technical Publications preview
AMX 4+
Brand: GE Pages: 56
GE AMX 4+ Technical Manual preview
AMX 4+
Brand: GE Pages: 132
GE AKTAprocess Site Preparation Manual preview
AKTAprocess
Brand: GE Pages: 16
GE Logiq 500 Advanced Reference Manual preview
Logiq 500
Brand: GE Pages: 474
BACtrack ELEMENT Product Manual preview
ELEMENT
Brand: BACtrack Pages: 16
Bartscher 1500/17 Original Instruction Manual preview
1500/17
Brand: Bartscher Pages: 28
Bartscher IV-65 Instruction Manual preview
IV-65
Brand: Bartscher Pages: 13
IBEX TS100 Quick Start Manual preview
TS100
Brand: IBEX Pages: 10
M-system R3 Series Instruction Manual preview
R3 Series
Brand: M-system Pages: 12
Datalogic Heron HD3430 Quick Reference Manual preview
Heron HD3430
Brand: Datalogic Pages: 48
PageFlip Firefly Quick Start Manual preview
Firefly
Brand: PageFlip Pages: 32
Taurus HS 100 Assembly Instructions Manual preview
HS 100
Brand: Taurus Pages: 24
Kellfri 27-V1500 Manual preview
27-V1500
Brand: Kellfri Pages: 12
Labelmate UCAT-S User Manual preview
UCAT-S
Brand: Labelmate Pages: 61
Labconco FreeZone Plus User Manual preview
FreeZone Plus
Brand: Labconco Pages: 62
Macht Dental POWER CLEAN Operation Instruction Manual preview
POWER CLEAN
Brand: Macht Dental Pages: 8
Madrigal Stiletto Quick Start Manual preview
Stiletto
Brand: Madrigal Pages: 5

Brands by name

Popular brands

Load more brands