manualshive.com logo in svg

BeamMed Sunlight Omnisense 7000S, User Manual

The BeamMed Sunlight Omnisense 7000S is a revolutionary diagnostic device used for bone health assessment. Ensure proper usage and maintenance of this cutting-edge tool with our comprehensive User Manual. Download it for free from our website manualshive.com and unlock the full potential of this remarkable product.

Share
Download
background image

    

User Guide 

  11-6

Desktop Utilities

Desktop

 when exiting Omnisense through 

Patient>Exit

. 

User Interface Language

The default user interface language of the Sunlight Desktop is 
English.

Changing the User Interface Language

S

TEP

 1 Change Language

To change the user interface language, click 

Options>User Interface Language

. Choose the 

appropriate language by clicking on the name of the 
appropriate language. Click 

OK

. The system will 

now use the chosen user interface language.

Regional Settings

The default regional settings of the Sunlight Desktop in the 
United States are USA (English) settings. Regional settings 
include date and time formats, decimal number formats, cur-
rency, and currency format.

Changing the Regional Settings

S

TEP

 1 Change Settings

To change the regional settings, click 

Options>Regional Settings

. Choose the appropriate 

regional settings by clicking on the name of the 
appropriate settings. Click 

OK

. The system will 

indicate if it requires a reboot after changing these 
settings, and will reboot automatically if this is 
required. 

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

GE MicroVersaTrip Plus Installation Instructions Manual preview
MicroVersaTrip Plus
Brand: GE Pages: 20
GE b30 Technical Reference Manual preview
b30
Brand: GE Pages: 252
Balanced Body Duet Manual preview
Duet
Brand: Balanced Body Pages: 12
Eagle Pro EL Series Instruction Sheet preview
EL Series
Brand: Eagle Pro Pages: 6
GE EntelliGuard G Instructions Manual preview
EntelliGuard G
Brand: GE Pages: 10
XTA C2 Operator'S Manual preview
C2
Brand: XTA Pages: 29
vc999 K4 Operating Instruction preview
K4
Brand: vc999 Pages: 59
Qtx RP4 User Manual preview
RP4
Brand: Qtx Pages: 3
Saferoad F1 Installation Instruction preview
F1
Brand: Saferoad Pages: 24
Panasonic WJHD309A - DIGITAL DISK RECORDER Network Operating Instructions preview
WJHD309A - DIGITAL DISK RECORDER
Brand: Panasonic Pages: 79
VeEX FX30 Quick Manual preview
FX30
Brand: VeEX Pages: 2
JB-Lighting P8 Operating Instructions Manual preview
P8
Brand: JB-Lighting Pages: 48
Facnor LS Installation Manual preview
LS
Brand: Facnor Pages: 33
TC Electronic M5000 Hardware Installation preview
M5000
Brand: TC Electronic Pages: 2
Bahco BBT80 Operating Instructions Manual preview
BBT80
Brand: Bahco Pages: 131
Bahco BBT60A Original Instructions Manual preview
BBT60A
Brand: Bahco Pages: 126
Datalogic Heron HD3430 Quick Reference Manual preview
Heron HD3430
Brand: Datalogic Pages: 48
PageFlip Firefly Quick Start Manual preview
Firefly
Brand: PageFlip Pages: 32

Brands by name

Popular brands

Load more brands