manualshive.com logo in svg

BeamMed Sunlight Omnisense 7000S, User Manual

The BeamMed Sunlight Omnisense 7000S is a revolutionary diagnostic device used for bone health assessment. Ensure proper usage and maintenance of this cutting-edge tool with our comprehensive User Manual. Download it for free from our website manualshive.com and unlock the full potential of this remarkable product.

Share
Download
background image

     

Omnisense 7000S/8000S     

10-11

Setting System Default Options

Figure 10.7   System Options dialog box — Scheduler screen

The table below explains the function of the fields in this tab.

Table 10.4  System Options — Scheduler Settings

Administration>Options>Scheduler

  

       

OK or Cancel

  

Screen Item

Function

Next Mea-
surement 
Due After

This screen item selects the default time 
period between measurements. The 
available options are: 1 year, 2 years or a 
period in months entered by the user. 

Example:

 If the option “1 year” is 

selected, and a measurement was per-
formed on December 1, 

2003

, the system 

will automatically schedule the patient’s 
next measurement to December 1, 

2004

, 

one year later.

Note:

 The factory default setting for all 

patients is one year between examina-
tions. The user is free to set any other 
desired default period, as described 
above, or a patient specific date, using 
the patient Scheduler form as described 
in “Measurement Scheduling,” page 7-6.

Summary of Contents for Sunlight Omnisense 7000S





























































































































































































































































































Reviews:

No comments

Related manuals for Sunlight Omnisense 7000S

NEILPRYDE X1 Manual preview
X1
Brand: NEILPRYDE Pages: 53
JAC PRO+ Translation Of Original User Instructions preview
PRO+
Brand: JAC Pages: 103
3Disc Heron IOS Quick Start Manual preview
Heron IOS
Brand: 3Disc Pages: 12
Ultimaker S7 Installation And User Manual preview
S7
Brand: Ultimaker Pages: 38
A&D UP-200 User Manual preview
UP-200
Brand: A&D Pages: 2
A&D RA3100 Omniace Instruction Manual preview
RA3100 Omniace
Brand: A&D Pages: 176
Federal 90 Series Troubleshooting Manual preview
90 Series
Brand: Federal Pages: 43
Tascam SX-1 Brochure & Specs preview
SX-1
Brand: Tascam Pages: 8
Keithley 7071 Instruction Manual preview
7071
Brand: Keithley Pages: 79
Kayakpro SUP ERGO Assembly Instruction Manual preview
SUP ERGO
Brand: Kayakpro Pages: 17
Yoshitake DS-1 Operation Manual preview
DS-1
Brand: Yoshitake Pages: 11
UNIS CUBE II Operating Manual preview
CUBE II
Brand: UNIS Pages: 16
Unique Automation Bathomatic Basic User Manual preview
Bathomatic Basic
Brand: Unique Automation Pages: 10
Additel 762 User Manual preview
762
Brand: Additel Pages: 139
Öhlins FCX 0301 Mounting Instructions preview
FCX 0301
Brand: Öhlins Pages: 8
?HC HC1200EB Quick Start Manual preview
HC1200EB
Brand: ?HC Pages: 2
ZIEHL-ABEGG ZA top SM315.100A Original Operating Instructions preview
ZA top SM315.100A
Brand: ZIEHL-ABEGG Pages: 76
Kellfri 26-GAATV360 Manual preview
26-GAATV360
Brand: Kellfri Pages: 44

Brands by name

Popular brands

Load more brands