Barco ICMP Service Manual Download Page 73

Page: 73 / 96

5. ICMP service procedure

5.2

Installing the ICMP

This procedure assumes that the projector has been made ICMP ready. In other words
the Card Cage slots wherein the ICMP has to be inserted are empty and the latest pro-
jector software package is installed.

AUTION

Wear a wrist band which is connected to the ground while handling the elec-

trostatic discharge sensitive parts.

Necessary tools

•

7mm

at screwdriver.

•

PH2 Phillips screwdriver.

•

ESD wrist band.

How to install the ICMP into the Card Cage?

1. Gently insert the ICMP in the guides of the Card Cage as illustrated below.

Caution:

Ensure that the both sides of the ICMP are captured by the guides inside the Card Cage
compartment. See detail in image below.

2. Push (apply a little pressure) on both handles until the ICMP is fully inserted and the connection is made

with the back plane.

Note:

All connections are made via the board to board connection with the back plane.

3. Alternately fasten the four screws (reference 1) at the front side of the ICMP. Use a PH2 Phillips screw-

driver.

Caution:

Ensure to tighten the screws alternately!

Image 5-3

R5906594 ICMP 09/11/2016

Summary of Contents for ICMP

































































































Search results

Summary of Contents for ICMP

Reviews:

Related manuals for ICMP

Brands by name

Popular brands

Barco ICMP, Service Manual

Search results

Summary of Contents for ICMP

Reviews:

Related manuals for ICMP

Brands by name

Popular brands