1-3
1
Torque Conversions
(ft-lb/N-m)
Tightening Torque
(General Bolts)
Break-In Procedure
A new ATV and an overhauled ATV engine require a
“break-in” period. The first 10 hours (or 200 miles) are
most critical to the life of this ATV. Proper operation
during this break-in period will help assure maximum
life and performance from the ATV.
During the first 10 hours (or 200 miles) of operation,
always use less than 1/2 throttle. Varying the engine
RPM during the break-in period allows the compo-
nents to “load” (aiding the mating process) and then
“unload” (allowing components to cool). Although it
is essential to place some stress on the engine compo-
nents during break-in, care should be taken not to
overload the engine too often. Do not pull a trailer or
carry heavy loads during the 10-hour break-in period.
When the engine starts, allow it to warm up properly.
Idle the engine several minutes until the engine has
reached normal operating temperature. Do not idle the
engine for excessively long periods of time.
During the break-in period, a maximum of 1/2 throttle
is recommended; however, brief full-throttle accelera-
tions and variations in driving speeds contribute to
good engine break-in.
After the completion of the break-in period, the engine
oil and oil filter should be changed. Other maintenance
after break-in should include checking of all pre-
scribed adjustments and tightening of all fasteners (see
Periodic Maintenance Chart in Section 2).
Gasoline - Oil -
Lubricant
RECOMMENDED GASOLINE
The recommended gasoline to use is 87 minimum
octane regular unleaded. In many areas, oxygenates
(either ethanol or MTBE) are added to the gasoline.
Oxygenated gasolines containing up to 10% ethanol,
5% methane, or 5% MTBE are acceptable gasolines.
When using ethanol blended gasoline, it is not neces-
sary to add a gasoline antifreeze since ethanol will pre-
vent the accumulation of moisture in the fuel system.
ft-lb
N-m
ft-lb
N-m
ft-lb
N-m
ft-lb
N-m
1
1.4
26
35.4
51
69.4
76
103.4
2
2.7
27
36.7
52
70.7
77
104.7
3
4.1
28
38.1
53
72.1
78
106.1
4
5.4
29
39.4
54
73.4
79
107.4
5
6.8
30
40.8
55
74.8
80
108.8
6
8.2
31
42.2
56
76.2
81
110.2
7
9.5
32
43.5
57
77.5
82
111.5
8
10.9
33
44.9
58
78.9
83
112.9
9
12.2
34
46.2
59
80.2
84
114.2
10
13.6
35
47.6
60
81.6
85
115.6
11
15
36
49
61
83
86
117
12
16.3
37
50.3
62
84.3
87
118.3
13
17.7
38
51.7
63
85.7
88
119.7
14
19
39
53
64
87
89
121
15
20.4
40
54.4
65
88.4
90
122.4
16
21.8
41
55.8
66
89.8
91
123.8
17
23.1
42
57.1
67
91.1
92
125.1
18
24.5
43
58.5
68
92.5
93
126.5
19
25.8
44
59.8
69
93.8
94
127.8
20
27.2
45
61.2
70
95.2
95
129.2
21
28.6
46
62.6
71
96.6
96
130.6
22
29.9
47
63.9
72
97.9
97
131.9
23
31.3
48
65.3
73
99.3
98
133.3
24
32.6
49
66.6
74
100.6
99
134.6
25
34
50
68
75
102
100
136
Type of Bolt
Thread Diameter
A (mm)
Tightening
Torque
(Conventional or 4 Marked Bolt)
5
12-36 in.-lb
6
36-60 in.-lb
8
7-11 ft-lb
10
16-25 ft-lb
(7 Marked Bolt)
5
24-48 in.-lb
6
6-8 ft-lb
8
13-20 ft-lb
10
29-43 ft-lb
CAUTION
Do not use white gas. Only Arctic Cat approved gaso-
line additives should be used.
Next
Back
Section
Table of Contents
Manual
Table of Contents
FOR ARCTIC CAT ATV DISCOUNT PARTS CALL 606-678-9623 OR 606-561-4983
www.mymowerparts.com
