CNC Setup Utility Manual
P/N 70000490C - Index
Index-6
All rights reserved. Subject to change without notice.
10-December-04
MC_1141, user definable variable #1141, 2-8
MC_1142, user definable variable #1142, 2-8
MC_1143, user definable variable #1143, 2-8
MC_1144, user definable variable #1144, 2-8
MC_1145, user definable variable #1145, 2-9
MC_1146, user definable variable #1146, 2-9
MC_1147, user definable variable #1147, 2-9
MC_1148, user definable variable #1148, 2-9
MC_1149, user definable variable #1149, 2-9
MC_1150, 3-D probe type, 2-10
MC_1151, nominal probe stylus diameter,
2-10
MC_1152, maximum stroke from home for
first pick, 2-10
MC_1153, RPM for calibration and tool
measurement, 2-10
MC_1154, probe orientation, 2-10
MC_1155, Z first pick, FAST feed-rate, 2-10
MC_1156, Z first pick, MEDIUM feed-rate,
2-10
MC_1157, Z first pick, SLOW feed-rate, 2-10
MC_1158, Z retract amount, 2-10
MC_1159, XY retract amount, 2-11
MC_1160, Z rapid to start position from
home, 2-11
MC_1161, diameter of tool probe gauge, 2-11
MC_1162, positioning feedrate normally, 2-11
MC_1163, first touch feedrate, 2-11
MC_1164, nominal probe stylus ball radius,
2-11
MC_1165, diameter of spindle probe gauge,
2-11
MC_1200, restore Editor to previous session,
2-12
MC_1201, show top line, 2-12
MC_1202, default insert mode, 2-12
MC_1203, auto tab to previous line’s position,
2-12
MC_1205, default tab width, 2-12
MC_1206, create backup program, 2-12
MC_1208, case sensitive find, 2-13
MC_1209, memory reserved from editor, 2-13
MC_1300, program directory pattern, 2-13
MC_1301, program directory, display mode,
2-13
MC_1302, program directory sort order, 2-13
MC_1303, automatically check disk at
startup, 2-13
MC_1305, directory for user program, 2-13
MC_1350, port, 2-14
MC_1351, baud, 2-14
MC_1352, parity, 2-14
MC_1353, data bits, 2-14
MC_1354, stop bits, 2-14
MC_1355, software, 2-14
MC_1375, default output device, 2-14
MC_1376, lines per page, 2-14
MC_1377, page heading, 2-14
MC_1378, line numbers, 2-14
MC_1381, wrap text, 2-14
MC_1394, delete backup files during
optimize, 2-13
MC_2000, X motor encoder connector, 2-15
MC_2001, X PWM output connector, 2-15
MC_2002, X inverter type, 2-15
MC_2003, X motor type, 2-15
MC_2004, X linear encoder connector, 2-16
MC_2005, X linear encoder sinewave period,
2-16
MC_2006, X linear encoder µm per sinewave,
2-16
MC_2007, X linear encoder type, 2-16
MC_2008, X linear encoder signal type, 2-16
MC_2009, X linear encoder phase, 2-16
MC_2010, X ballscrew pitch, 2-17
MC_2011, X number of teeth motor, 2-17
MC_2012, X number of teeth ballscrew, 2-17
MC_2013, X motor encoder phase, 2-17
MC_2014, X DC bus voltage, 2-17
MC_2015, X i
2
t guarding, 2-17
MC_2016, X commutation offset speed (rpm),
2-17
MC_2017, X commutation offset angle (deg),
2-17
MC_2018, X velocity filter, 2-17
MC_2020, X current control gain N<Nom
(mV/A), 2-18, 5-2
MC_2021, X current control gain N>Nom
(mV/A), 2-18
MC_2022, X vel. control prop. gain (mAs/rev),
2-18, 5-6, 5-7
MC_2023, X vel. control integral timecons
(.1ms), 2-18, 5-6, 5-7
MC_2024, X vel. control integral limit (ms),
2-18
MC_2025, X vel. control diff. gain
(.1mAs
2
/rev), 2-18
MC_2026, X pos. control prop. gain (1/min),
2-18, 5-9
MC_2027, X pos. control output limit (rpm),
2-19
MC_2028, X velocity feedfwd. gain, 2-19, 5-9
