manualshive.com logo in svg

Analog Devices ADRV9001, User Manual, Page: 257 / 338

Share
Download
Analog Devices ADRV9001 User Manual Download Page 257

Preliminary Technical Data 

UG-1828 

 

Rev. PrC | Page 257 of 338 

This approach uses the ADRV9001 internal LDOs to generate 1.0 V for all internal blocks. Figure 246 outline power supply routing 
recommendations for this architecture.  

 

Figure 246. ADRV9001 Power Supply Domains with Connection Guidelines, All Internal LDOs in Use 

•

 

Power supply optimization, higher risk (use noise sensitive 1.0V analog), 5 power domains: 
•

 

1.8 V digital,  

•

 

1.8 V analog,  

•

 

1.3 V analog,  

•

 

1.0 V digital, 

•

 

1.0 V analog, 

This approach that uses some of ADRV9001 internal LDOs to generate 1.0 V for internal blocks. For remining blocks it expect the 1.0 V 
to be delivered from external power source. Figure 247 outline power supply routing recommendations for this architecture. 

•

 

For domains shown in Figure 247 that should be powered through a ferrite bead (FB), care should be taken to place the ferrite 
beads near the ADRV9001 supply pins. The ferrite beads should also be spaced to ensure their electric fields do not influence 
each other. The ferrite bead should supply a trace with a reservoir capacitor connected to it. That trace should then be shielded 
with ground and provide power to input power pin.  

 

TRACE TO 1.8V DIG

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.3V

CONNECT 2 PINS TOGETHER

WITH 4.7µF CAPACITOR

CONNECT 2 PINS TOGETHER

WITH 4.7µF CAPACITOR

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.8V Tx2

TRACE WITH FB TO 1.8V ANLG

4.7µF CAPACITOR

4.7µF CAPACITOR

4.7µF CAPACITOR

TRACE WITH FB TO 1.8V Tx1

TRACE TO 1.0V DIG.

HIGH CURRENT

TRACE WITH FB TO 1.3V
TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.3V

TRACE WITH FB TO 1.8V ANLG

4.7µF CAPACITOR

4.7µF CAPACITOR

4.7µF CAPACITOR

24159-

195

Summary of Contents for ADRV9001



















































































































































































































































































































































Reviews:

No comments