SEND_COMMANDs
30
Mio Modero R-4 Remote - Instruction Manual
Page Commands (Cont.)
@PHE
Set the hide effect for the specified popup page to the named hide effect.
Syntax:
SEND_COMMAND <DEV>,"'@PHE-<popup page name>;<hide effect name>'"
Variables:
• popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
• hide effect name = Refers to the popup effect names being used.
Example:
SEND_COMMAND Panel,"'@PHE-Popup1;Slide Left'"
Sets the Popup1 hide effect name to 'Slide Left'.
@PHP
Set the hide effect position. Only 1 coordinate is ever needed for an effect, however the command will specify both. This
command sets the location at which the effect will end at.
Syntax:
SEND_COMMAND <DEV>,"'@PHP-<popup page name>;<x coordinate>,<y coordinate>'"
Variable:
• popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Device,"'@PHP-Popup1;75,0'"
Sets the Popup1 hide effect x-coordinate value to 75 and the y-coordinate value to 0.
@PHT
Set the hide effect time for the specified popup page.
Syntax:
SEND_COMMAND <DEV>,"'@PHT-<popup page name>;<hide effect time>'"
Variables:
• popup page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
• hide effect time = Given in 1/10ths of a second.
Example:
SEND_COMMAND Device,"'@PHT-Popup1;50'"
Sets the Popup1 hide effect time to 5 seconds.
@PPA
Close all popups on a specified page. If the page name is empty, the current page is used. This command works in the same way
as the 'Clear Page' command in TPDesign4.
Syntax:
SEND_COMMAND <DEV>,"'@PPA-<page name>'"
Variable:
• page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Device,"'@PPA-Page1'"
Close all popups on Page1.
@PPF
Deactivate a specific popup page on either a specified page or the current page. If the page name is empty, the current page is
used (see example 2). If the popup page is part of a group, the whole group is deactivated. This command works in the same way
as the 'Hide popup' command in TPDesign4.
Syntax:
SEND_COMMAND <DEV>,"'@PPF-<popup page name>;<page name>'"
Variables:
• popup page name = 1 - 50 ASCII characters. Name of the popup page.
• page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example 1:
SEND_COMMAND Device,"'@PPF-Popup1;Main'"
Deactivates the popup page 'Popup1' on the Main page.
Example 2:
SEND_COMMAND Device,"'@PPF-Popup1'"
Deactivates the popup page 'Popup1' on the current page.
@PPG
Toggle a specific popup page on either a specified page or the current page. If the page name is empty, the current page is used
(see example 2). Toggling refers to the activating/deactivating (On/Off) of a popup page. This command works in the same way
as the 'Toggle Popup' command in TPDesign4.
Syntax:
SEND_COMMAND <DEV>,"'@PPG-<popup page name>;<page name>'"
Variables:
• popup page name = 1 - 50 ASCII characters. Name of the popup page.
• page name = 1 - 50 ASCII characters. Name of the page the popup is displayed On.
Example:
SEND_COMMAND Device,"'@PPG-Popup1;Main'"
Toggles the popup page 'Popup1' on the 'Main' page from one state to another (On/Off).
Example 2:
SEND_COMMAND Device,"'@PPG-Popup1'"
Toggles the popup page 'Popup1' on the current page from one state to another (On/Off).
