manualshive.com logo in svg

Altigen AltiWare ACC 5.2, Administration Manual

Share
Download
Altigen AltiWare ACC 5.2 Administration Manual Download Page 379

AltiWare ACC 5.2 Administration Manual 367

A

P P E N D I X

B

Required Service Parameters

This appendix identifies the recommended and supported parameters for T1, PRI, and 
E1 service and provides you with the information needed when you make your service 
request.

Service Parameters/Request Information for T1

To subscribe to T1 service, certain parameters are required to establish service. The 
information provided below identifies the recommended and supported parameters for 

T1 service. When ordering T1 service, provide the following service request information:

Equipment Information

•

PBX Manufacturer—AltiGen Communications, Inc.

•

CSU/DSU—ADTRAN T1 ACE (recommended) or other CSU/DSU

Technical Information for T1 with Voice

Signaling Protocol:

•

E&M Wink Start (recommended) 

•

E&M Immediate Start

•

Ground Start

•

Loop Start (not recommended)

Trunk Type:

•

DID

•

2-Way DID (recommended)

•

DOD

Framing:

•

Super Frame (SF)/D4

•

Extended Super Frame (ESF) (recommended)

Line Coding:

•

Alternate Mark Inversion (AMI)

•

B8ZS (recommended)

Summary of Contents for AltiWare ACC 5.2
















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands