manualshive.com logo in svg

Altigen AltiWare ACC 5.2, Administration Manual

Share
Download
Altigen AltiWare ACC 5.2 Administration Manual Download Page 155

Chapter 12:  Trunk Configuration

AltiWare ACC 5.2 Administration Manual 143

SIP Trunk Properties 

Traditionally telecom trunks are from your local carrier’s PSTN switch and the dial tone 

is provided via either analog trunks or T1/PRI digital trunks. A new type of service called 
“IP Dial Tone,” which allows you to dial a long distance call at a lower rate, is available. 
IP Dial Tone is delivered through your IP data network, and the service provider can be 

anywhere in the world, as long as the VoIP data packets can be routed properly.
If you have SIP-based IP dial tone service from an Internet Telephony Service Provider 
(ITSP), you need to configure SIP trunk channels to connect the service. Before you 
start, note the following:

•

An AltiGen SIP Trunking channel is licensed. You need to buy and register a license 
to be able to configure this option.

•

AltiGen does not guarantee the voice quality of the SIP dial tone coming from your 
service provider. You need to work with your data service and SIP trunking service 

provider to make sure adequate QoS is provisioned for your WAN service.

•

AltiGen does not guarantee SIP trunk implementation will work with all SIP Dial Tone 
service providers. You need to verify that your SIP Dial Tone service provider 
supports the following:

•

G.711, G.723.1, G.729 codec

•

RFC 2833 for DTMF tone delivery

•

SIP MD5 authentication with SIP registration

•

If AltiServ is behind NAT, verify that your SIP SP can support this configuration.

When subscribing to SIP Dial Tone service, typically your service provider will provide 
you with the information required in the configuration dialog box shown in Figure 5 on 
page 144. Enter these service parameters to each SIP trunk channel configuration 

individually.

Note:

This is signal only trunks. Make sure you have enough IP resource boards to cover 
your needs.

Important:

You need to add the SIP Trunk service provider’s IP address to the IP Device 
Range in AltiEnterprise Manager and select the proper codec profile for this 
service. See “Assigning Codec Profiles to IP Addresses” on page 306. Failure 
to do this step may cause no voice path, even if the SIP Trunk channel shows 

the call is connected.

Configuring a SIP Trunk

To open a trunk configuration dialog box for a SIP trunk, do one of the following:

•

In the 

Trunk Configuration

 window, select a SIP trunk type, click the 

Trunk 

Properties

 button, then click the 

SIP Trunk Configuration

 button.

•

In the 

Board View

 window, double-click a SIPSP board type, click the 

Board 

Configuration

 button, then click the 

SIP Trunk Configuration

 button.

Summary of Contents for AltiWare ACC 5.2
















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands