manualshive.com logo in svg

Altigen AltiWare ACC 5.2, Administration Manual

Share
Download
Altigen AltiWare ACC 5.2 Administration Manual Download Page 125

Chapter 11:  Board Configuration

AltiWare ACC 5.2 Administration Manual 113

Important:

To implement some board configuration changes, you must shut down and 
restart by choosing 

Services > Shut Down All Services

 (which also closes 

AltiWare) and then restarting AltiWare. If this is necessary, a message will 

pop up telling you so.

Using the Triton Resource Board

The Triton resource board requires no configuration. Board resources are available when 

the board is installed.
The resource board has a maximum of 12 bridges for: 

•

6-party conferencing. When an extension is trying to make a conference call, the 
system will try to use the conference bridge on the resource board first. If conference 
bridges on the resource board are all busy, the system will use the conference 
bridges on the extension board, analog or VoIP board.

•

Workgroup supervisor silent monitoring, barge-in, and coaching.

For example, if two supervisors are coaching agents, only 10 bridges are left for 6-party 
conferencing.

Notes

:

If a supervisor tries to perform silent monitoring, barge-in, or coaching 

and there is no 

resource board in the system,

 

the supervisor will hear an

 

error tone

.

If the supervisor is using an IP phone, then 

Connect Voice Stream to Server

 should 

be checked in the Extension Configuration window so that the system can pull the caller 
and agent's voice stream to the resource board to allow the supervisor to tap into the 

conversation.

Using the Triton MeetMe Conference Board

The Triton MeetMe conference board requires no configuration. Board resources are 

available when it is installed. You do have to assign a MeetMe Conference extension 
(select 

PBX > MeetMe Conference Configuration

).

One MeetMe conference board is supported in a system.

Note:

In a multiple AltiGateways installation, the MeetMe conference board can be in 
any AltiGateway server. 

Configuring the Quantum Board

Double-click the Quantum board in the 

Boards

 window to open the 

Board 

Configuration

 window, similar to Figure 2 on page 112. See attribute descriptions 

below Figure 2. Note the following additional information:

This option is in the 
Extension Configuration window

Summary of Contents for AltiWare ACC 5.2
















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands