Altigen AltiWare ACC 5.2 Administration Manual Download Page 287

Page: 287 / 399

Chapter 22: Workgroup Configuration

AltiWare ACC 5.2 Administration Manual 275

•

To an

Outside Number

—this option is available if it is allowed in the

Other Call

Restrictions

option in the

Restriction

tab, as discussed in “Setting Other Call

Restrictions” on page 203.
If you choose

Outside Number

, select a trunk or route access code to use in the

small drop-down list on the left, and type in the full prefix and phone number.

•

Line Park

—if configured, select a

Line Park

group from the drop-down list.

Handling Unanswered Calls

The

Enable No Answer Handling

configuration provides options for handling calls

when the system rings the first available agent and the call is not answered. If

all

agents

in the workgroup are rung and no one answers the call, the system will use the Group
RNA/Logout Handling rule.

Enable No Answer Handling

is not available if Intra Group

Call Distribution is set to

Ring All Available Members

To configure this option, check the

Enable No Answer Handling

box.

Select one of the following forwarding options for no answer call handling:

•

Next Group Member

- ring the next available agent until all available agents are

rung. If all agents are busy, caller will stay in the workgroup queue.

•

Extension

- take the call out of the workgroup and forward it to an extension.

•

Group

- take the call out of workgroup and forward it to another group.

•

Group Voice Mail

- transfer the caller to the workgroup voice mail when the first

available agent does not answer the call.

•

Member Voice Mail

- transfer the caller to the first available agent's voice mail if

this agent does not answer the call.

•

- take the call out of the workgroup and forward it to an auto attendant.

•

Line Park

- take the call out of the workgroup and forward it to a Line Park group.

Set RNA Agent Logout Check Box

Select this option to have the system automatically log out an agent extension from a
workgroup if RNA is encountered.

Number of Rings Before Handling

If you select

Ring All Available Members

in the Intra Group Call Distribution section,

then specify the

Number of Rings before Handling

, using the scroll box beside that

option. The number of rings is the total number of times agents are rung before the call
is handled by the Group RNA/Logout Handling configuration

Setting IntraGroup Call Distribution

The IntraGroup Call Distribution options let you set the handling of normal inbound calls:
how to route the incoming call to a workgroup agent, using one of the following options:

Summary of Contents for AltiWare ACC 5.2
















































































































































































































































































































































































































Search results

Summary of Contents for AltiWare ACC 5.2

Reviews:

Brands by name

Popular brands

Altigen AltiWare ACC 5.2, Administration Manual

Search results

Summary of Contents for AltiWare ACC 5.2

Reviews:

Brands by name

Popular brands