manualshive.com logo in svg

Altigen AltiWare ACC 5.2, Administration Manual

Share
Download
Altigen AltiWare ACC 5.2 Administration Manual Download Page 247

Chapter 18:  Mobile Extension Configuration

AltiWare ACC 5.2 Administration Manual 235

Voice Mail for Mobile Extensions

When the mobile extension phone is turned off or busy, messages can go to the 

extension’s voice mail in AltiWare or to the mobile phone’s voice mail:

•

To send a call to the mobile extension’s voice mail in AltiWare, check the 

Press any 

key to answer call

 check box.

•

To send a call to the mobile phone’s voice mail, the 

Press any key to answer call

 

check box must be 

un

checked.

Mobile Extension Limitations

•

Quantum analog trunk is not supported.

•

Only PRI mobile trunks can deliver Caller ID information to the Mobile Extension.

•

A Mobile Extension cannot support Centrex transfer.

•

After adjusting the number of mobile extension ports in a mobile extension board, 
AltiWare must be restarted for the changes to take effect.

•

Cannot deliver caller name to the Mobile Extension.

•

Does not support Message Waiting Indicator on Mobile Extension device. (Use 
Message Notification as a work-around).

•

Since the DTMF key 

*

 is used for simulating the FLASH signal, there is no way to 

send 

*

 to the system. 

•

The RNA for Mobile Extension may not be accurate, because the system ring count 
may not be in sync with the Mobile Extension device ring count.

•

When placing calls to Mobile Extensions that are cell phones, if the cell phone is out 
of signal range, the caller may hear long periods of silence. You can check the 

Press 

any key to answer call

 option to prevent this problem.

•

Only analog trunks can be allocated as dedicated mobile trunks.

Summary of Contents for AltiWare ACC 5.2
















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands