manualshive.com logo in svg

Altigen AltiWare ACC 5.2, Administration Manual

Share
Download
Altigen AltiWare ACC 5.2 Administration Manual Download Page 16

Chapter 1:  Overview

4

AltiWare ACC 5.2 Administration Manual

•

SIP Extension Home Gateway Assignment 

- This feature affects only multi-

chassis installations. The primary purpose of this feature is to allocate resources for 
the IP phone when conferencing, silent monitoring, barging-in, and conversation 

recording. This allows the administrator to configure sufficient VoIP resources in an 
AltiGateway chassis for IP phone users assigned to this home AltiGateway. 

•

SIP Trunk Support 

- An increasing number of service providers offer dial tone 

through data network using SIP protocol. Beginning with Release 5.1, AltiGen’s 
system can connect to IP-based trunking service providers via SIP. 

•

SIP IP Phone (IP600, IP710, IP705)

 - Through firmware upgrade, all AltiGen IP 

phones can run SIP protocols.

•

SIP NAT Traversal

 - This feature allows AltiWare to connect to a remote SIP phone 

or IPTalk behind NAT without changing the NAT setting at the remote location.

•

Support for RFC 2833 (DTMF payload embedded with RTP) 

- Supported in SIP 

trunks only. This feature helps to resolve DTMF tone detection and regeneration 

when using G.723.1 or G.729 codec. Basically low bit rate compression will distort 
DTMF tone during compression. The far end device may not be able to recognize the 
DTMF digits. RFC 2833 specifies a separate RTP payload format to carry DTMF 

information to ensure the other side can recognize the tone properly.

•

Support for both SIP and H.323 Tie Trunk 

- When setting up a system-to-system 

VoIP tie trunk, either SIP or H.323 protocol can be used.

Multi-Site Enterprise Management - AltiEnterprise Manager

•

Replaces DINA Manager and IP Dialing Table in 5.0A

•

VoIP Domain 

- when networking multiple AltiGen systems from different sites, one 

system can be assigned as the VoIP Domain controller to propagate configuration 
data to member systems.

•

Directory Synchronization

 - when a new extension is added to one of the member 

systems and configured as a Global extension, the VoIP Domain controller will 
propagate this extension to all member systems. Every member system within the 

VoIP Domain can see the extension number plan of the other systems.

•

Multi-site Call Routing

 - when a user dials an extension number which is not a 

local extension number, the system searches the VoIP Domain extension list. If a list 
is found, the system will dial the number by using the IP address and extension 
number stored in the VoIP Domain extension list.

•

VoIP Domain User Management

 - VoIP Domain controller can resolve the conflict 

if duplicated extension numbers are created in different member systems. This 

feature also manages extension relocation. When an extension user is relocated to 
another member system, its voice mail and greeting can be relocated as well.

•

Global Least Cost Routing 

- when multiple systems are in different area codes or 

countries, the administrator can set up Global Least Cost Routing to route long 
distance or international calls through member systems. The routing rules are 

propagated to all members automatically.

•

Global IP Dialing Table 

- In the 5.1 Release, the IP Dialing Table moved to 

AltiEnterprise Manager. The IP Dialing Table configuration is used to create location-
based routing in the AltiEnterprise. Beginning with Release 5.1, the IP Dialing Table 
supports hop-off blocking by location to prevent unnecessary hop-off calling.

Summary of Contents for AltiWare ACC 5.2
















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands