FS2 Frame Synchronizer/Converter v3.0 43 www.aja.com
1.1 Authentication
This parameter enables or disables an authentication login requirement. By
default this parameter is set to Disabled.
When you select Login via the front panel parameter, you must then go to the
browser interface to perform a login each time you access the FS2. The browser
presents the login screen first, requiring you to log in before you can access any
other browser screens. The password is initially set to the default value, but you
can change it using the Remote browser screen.
The default password is password.
NOTE: If authentication is used, it provides only a minimum security safeguard against
unauthorized use of the FS2. The authentication mechanism is simple and does
not provide robust security.
Disabled
(default)
Login
Disables the requirement for a login password. No password is
needed.
Login is required via the web browser interface before changes can
be made in FS2 configuration.
2.1–4 GPI IN 1–4 Response
The setting of this parameter determines what happens when a GPI trigger is
received at the FS2’s GPI Inputs (1–4). A GPI Trigger is defined as a TTL low voltage
level (0 to 0.8V with respect to its isolated ground pin). The GPI interface pinout
and specifications are discussed in
. Input video sources
selected by GPI trigger remain selected until the trigger is released. GPI Inputs
light the front panel EXT LED when triggered.
No Action
(default)
PRESET 1–10
Vid1 Freeze
Vid1 SDI1 In
Vid1 SDI2 In
Vid1 SDI DLink
Vid1 Fiber1 In
Vid1 Fiber2 In
Vid1 Fbr DLink
Vid1 HDMI In
Vid1 Cmpst In
Vid1 Cmpnt In
Vid1 ARC Off
Vid1 ARC LTBX
Vid1 ARC H CP
Vid1 ARC PLBX
Vid1 ARC V CP
Vid1 ARC 14x9
Vid1 DC Crop
Vid1 DC ANA
Vid1 DC 14x9
Vid1 DC Auto AFD
Vid1 DC LTBX
Vid1 UC 4x3 PB
Vid1 UC 14x9 PB
Vid1 UC FLSCR
Vid1 UC LB FUL
Vid1 UC WDZM
Vid2...
Performs no action.
Recalls the specified PRESET configuration.
Freezes the current video frame at its outputs. Freezing stops when the GPI
trigger is released.
Selects SDI1 as the Vid1 video input.
Selects SDI2 as the Vid1 video input.
Selects Dual-Link mode for the SDI input.
Selects Fiber1 as the Vid1 video input.
Selects Fiber2 as the Vid1 video input.
Selects Dual-Link mode for the Fiber input.
Selects HDMI In as the Vid1 video input
Selects Composite In as the Vid1 video input.
Selects Component In as the Vid1 video input.
Turns Off SD to SD aspect ratio conversion.
Converts 16:9 anamorphic video to letterbox.
Converts 16:9 anamorphic video to 4:3 standard (H crop—crops left and
right edges of video).
Converts 4:3 standard video to 16:9 anamorphic (pillarbox).
Converts letterbox video to 16:9 anamorphic (V crop).
Converts 16:9 anamorphic video to 14:9 cropped.
Downconverts HD source to cropped 4x3 picture.
Downconverts HD source to anamorphic picture.
Downconverts HD source to 14x9 picture.
Downconverts HD source automatically using the best mode for the input
video Active Format Description (AFD) code.
Downconverts HD source to letterbox picture.
Upconverts SD source to 4x3 pillarbox.
Upconverts SD source to 14x9 pillarbox.
Upconverts SD source to full screen.
Upconverts SD source from letterbox to full.
Upconverts SD source to a wide zoom.
Repeat the above for Vid2 except that UC Wide Zoom is replaced by Vid2
UC CSTM, which Upconverts an SD source to a user-specified format.