manualshive.com logo in svg

ADTRAN DS3-PSM, Installation And Maintenance Practice

Share
Download
ADTRAN DS3-PSM Installation And Maintenance Practice Download Page 92

Total Access 3000 DSLAM DS3 Primary Switch Module Installation and Maintenance Practice

82

 

61181041L3-5A

MDE Link Configuration Menu

The MDE Link Configuration menu (see 

Figure 41

) is used to display the MDE configuration 

status. This is a dynamic menu that displays available options based upon input. Shelf 1 is 
the Primary Shelf and shelves 2 through 6 are Expansion shelves. Only one shelf can be 
added or removed at a time, and only in numerical order. For instance, Shelf 4 must be 
present before Shelf 5 can be added. All six options to add or remove a shelf are not displayed 
at the same time.

Figure 41.  MDE Link Configuration Menu

The MDE Link Configuration menu options are shown in 

Table 45

.

Table 45.  MDE Link Configuration Menu Options

Option 

Description

Function

1

Shelf 1

This field displays Shelf 1 (the Primary Shelf) as either Shelf 
Present or Shelf Removed.

2

Shelf 2

This field displays Shelf 2 as either Shelf Present or Shelf 
Removed.

3

Shelf 3

This field displays Shelf 3 as either Shelf Present or Shelf 
Removed.

4

Shelf 4

This field displays Shelf 4 as either Shelf Present or Shelf 
Removed.

5

Shelf 5

This field displays Shelf 5 as either Shelf Present or Shelf 
Removed.

6

Shelf 6

This field displays Shelf 6 as either Shelf Present or Shelf 
Removed.

Shelf: 1 Slot: B               Total Access System                    MM/DD/YY HH:MM
                                                                ONLINE

                     MDE Link Configuration

                         Shelf 1 : SHELF PRESENT
                         Shelf 2 : SHELF PRESENT
                         Shelf 3 : SHELF PRESENT
                         Shelf 4 : SHELF PRESENT
                     5.  Shelf 5 : SHELF PRESENT
                     6.  Shelf 6 : SHELF REMOVED

                         Shelf 1 Link Status : LINK UP
                         Shelf 2 Link Status : LINK UP
                         Shelf 3 Link Status : LINK UP
                         Shelf 4 Link Status : LINK UP
                         Shelf 5 Link Status : LINK UP
                         Shelf 6 Link Status : LINK DOWN

                     Selection:

Summary of Contents for DS3-PSM











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands