manualshive.com logo in svg

ADTRAN DS3-PSM, Installation And Maintenance Practice

Share
Download
ADTRAN DS3-PSM Installation And Maintenance Practice Download Page 45

Menu Trees

61181041L3-5A

 35

PSM Advanced Provisioning Menu

The PSM Advanced Provisioning menu (see 

Figure 17

) is used to provision PSM specific and 

subscriber interface options.

Figure 17.  PSM Advanced Provisioning Menu

The PSM Advanced Provisioning menu options are shown in 

Table 11

.

Table 11.  PSM Advanced Provisioning Menu Options

Option 

Description

Function

PSM Specific Options

1

Service State

This option is used to provision the service state of the DS3-
PSM. The following service states are available:

• In Service: In this state, the DS3-PSM passes data; 

alarms are generated for error conditions.

• Out of Service-Maintenance: In this state, the DS3-PSM 

passes data; alarms are suppressed.

2

OAM Identification

This option is used to set and display the unique OAM 
identifier. An OAM identifier is used as a point of origin to 
identify OAM cells.

Maximum Network 
VC/VPs

This field displays the maximum number of VC/VPs to be 
used by the network.

4

Linked Provisioning

This option is used to enable or disable linked 
provisioning. When enabled, the provisioning of the online 
DS3-PSM is written to the offline DS3-PSM.

Shelf: 1 Slot: B               Total Access System                    MM/DD/YY HH:MM
                                                                ONLINE

                          PSM Advanced Provisioning

     PSM Specific Options

     1.  Service State            : IN SERVICE
     2.  OAM Identification       : 6A:6A6A6A6A6A6A6A6A6A6A6A6A6A6A6A
         Maximum Network VC/VPs   : 8192
     4.  Linked Provisioning      : ENABLE
     5.  Reserved Voice VPI       : 0
     6.  Cell Buffer, CAC, & Policing Options
     7.  Alarms Provisioning

     Subscriber Interface Advanced Options

     8.  Invalid cells to exit Sync state   : 7
     9.  Valid cells to enter Sync State    : 6
     10. Restore Factory Defaults
     Selection:

                            '?' - System Help Screen

Summary of Contents for DS3-PSM











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands