manualshive.com logo in svg

ADTRAN DS3-PSM, Installation And Maintenance Practice

Share
Download
ADTRAN DS3-PSM Installation And Maintenance Practice Download Page 67

Menu Trees

61181041L3-5A

 57

ILMI Provisioning Screen

The ILMI Provisioning Screen (see 

Figure 29

) is used to set Interim Local Management 

Interface (ILMI) provisioning settings. The ILMI Provisioning Screen is accessed by pressing 
the 

I

 hot key on the ATM Provisioning Screen - Shelf # Slot # Port # menu.

Figure 29.  ILMI Provisioning Screen

The ILMI Provisioning Screen options are shown in 

Table 29

.

Table 29.  ILMI Provisioning Screen Options

Option 

Description

Function

1

ILMI

This option is used to enable or disable ILMI.

2

VPI

This option is used to set the VPI value to a number from 0 
to 255.

3

VCI

This option is used to set the VCI value to a number from 0 
to 511.

4

Addr Reg

This option is used to enable or disable Address Registra-
tion.

5

Auto Config

This option is used to enable or disable Automatic Configu-
ration.

6

Device Type

This option is used to set the Device Type to one of the fol-
lowing types:

• User
• Network

Shelf: 1 Slot: B               Total Access System                    MM/DD/YY HH:MM
                                                                ONLINE

                           ILMI PROVISIONING SCREEN
                          Shelf: 1 Slot 1 : Port  1
         1.  ILMI                : DISABLE
         2.  VPI                 : 0
         3.  VCI                 : 16
         4.  Addr Reg            : DISABLE
         5.  Auto Config         : ENABLE
         6.  Device Type         : USER
         7.  UNI Type            : PUBLIC
         8.  Get Next Timer      : 4
         9.  Set Req Timer       : 4
         10. Get Req Timer       : 5
         11. Max Svpc Vpi        : 255
         12. Max Svcc Vpi        : 255
         13. Min Svcc Vci        : 32
             ILMI Status         : Link Down
         Selection:

Summary of Contents for DS3-PSM











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands