manualshive.com logo in svg

ADTRAN DS3-PSM, Installation And Maintenance Practice

Share
Download
ADTRAN DS3-PSM Installation And Maintenance Practice Download Page 90

Total Access 3000 DSLAM DS3 Primary Switch Module Installation and Maintenance Practice

80

 

61181041L3-5A

Software Upgrade Menu

The Software Upgrade menu (see 

Figure 40

) is used to upgrade software, verify code revision, 

and restore all options to factory defaults on the DS3-PSM.

Figure 40.  Software Upgrade Menu

The Software Upgrade menu options are shown in 

Table 43

.

Table 43.  Software Upgrade Menu Options

Option 

Description

Function

1

Transfer Protocol

This option is used to select one of the following transfer 
protocol types:

• YMODEM
• TFTP

2

SCU To MUX Baud Rate

This option is used to select one of the following PCU to MUX 
baud transfer rates (in Kilobytes):

• 115.2K
• 57.6K
• 38.4K

3

TFTP Filename

This option is used to input the name of the file to transfer.

4

Start Transfer

This option is used to start transferring the specified file 
with the above parameters.

5

Restore Card Factory 
Defaults and Reset

This option resets ALL defaults on the DS3-PSM to factory 
defaults.

Shelf: 1 Slot: B               Total Access System                    MM/DD/YY HH:MM
                                                                ONLINE

       Software Upgrade                                          Shelf  1 of  6
       1.  Transfer Protocol     : TFTP
       2.  SCU To MUX Baud Rate  : 115.2K
       3.  TFTP Filename         : 1181041l3_a00_33.bin
       4.  Start Transfer
       5.  Restore Card Factory Defaults and Reset
       6.  Restart Card with Latest Code

       App Software Rev          : A00.33
       App Code Chksum           : a217
       Boot Software Rev         :
       Boot Code Chksum          : 0

       Download Status           : No Status

       (N)ext, (P)revious, All (E)xpansion Shelves, Selection:

Summary of Contents for DS3-PSM











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands