manualshive.com logo in svg

ADTRAN DS3-PSM, Installation And Maintenance Practice

Share
Download
ADTRAN DS3-PSM Installation And Maintenance Practice Download Page 89

Menu Trees

61181041L3-5A

 79

PNNI Switch Provisioning - Lowest Level Node Menu
The PNNI Switch Provisioning - Lowest Level Node menu (see 

Figure 39

) is used to provision 

Private Network-to-Network Interface (PNNI) options.

Figure 39.  PNNI Switch Provisioning - Lowest Level Node Menu

The PNNI Switch Provisioning - Lowest Level Node menu options are shown in 

Table 42

.

Table 42.  PNNI Switch Provisioning - Lowest Level Node Menu Options

Option 

Description

Function

1

Admin Status

This option is used to set the Admin Status to Up or Down.

2

Level

This option is used to enter a number from 0 to 104.

3

ATM address

This option is used to enter the ATM address in the format 
displayed.

4

Node ID

This option is used to enter the Node ID in the format 
displayed.

5

Peer group ID

This option is used to enter the Peer group ID in the format 
displayed.

6

Domain name

This option is used to enter an alphanumeric string of up to 
19 characters.

7

Leadership priority

This option is used to enter a number from 0 to 205.

8

Auto ID setup

This option is used to automatically configure the Node ID 
and Peer Group ID based on the ATM address that is 
previously configured.

Shelf: 1 Slot: B               Total Access System                    MM/DD/YY HH:MM
                                                                ONLINE

                 PNNI switch provisioning - Lowest level node

 1.  Admin status        : Down
 2.  Level               : 96
 3.  ATM address         : 00-0000:00000000000000000000-000000000000.00
 4.  Node ID             : 60:A0(00-0000:00000000000000000000-000000000000.00)
 5.  Peer group ID       : 60:00000000000000000000000000
 6.  Domain name         :
     Leadership priority : 0
 8.  Auto ID setup

 Selection:

                           '?' - System Help Screen

Summary of Contents for DS3-PSM











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands