manualshive.com logo in svg

ADTRAN DS3-PSM, Installation And Maintenance Practice

Share
Download
ADTRAN DS3-PSM Installation And Maintenance Practice Download Page 62

Total Access 3000 DSLAM DS3 Primary Switch Module Installation and Maintenance Practice

52

 

61181041L3-5A

ATM Provisioning Screen - Shelf # Slot # Port # Menu

The ATM Provisioning Screen - Shelf # Slot # Port # menu is displayed when the ATM Provi-
sioning (PORT) option is selected from the 

Provisioning Menu

. The ATM Provisioning Screen - 

Shelf # Slot # Port # menu (see 

Figure 27

) is used to set parameters to establish a data path 

between the PSM and individual ports on each access module.

Figure 27.  ATM Provisioning Screen - Shelf # Slot # Port # Menu

The ATM Provisioning Screen - Shelf # Slot # Port # menu options are shown in 

Table 26

.

Table 26.  ATM Provisioning Screen - Shelf # Slot # Port # Menu Options

Option 

Description

Function

1

Port ID

This option selects a specific shelf, slot, and port to review or 
modify provisioning settings.

2

Service Mode

This option is used to provision the service state of the 
selected port. Each individual port can be placed in one of 
the following service states:

• In Service: In this state, the DS3-PSM passes data, and 

alarms are generated for error conditions. Provisioning, 
activation of test modes, and software downloads are not 
available.

• Out of Service-Maintenance: In this state, the DS3 Port 

passes data, but alarms are suppressed. Provisioning, 
activation of test modes, and software downloads are 
available.

The default state is Out of Service-Maintenance.

Shelf: 1 Slot: B               Total Access System                    MM/DD/YY HH:MM
                                                                ONLINE

                           ATM PROVISIONING SCREEN
                          Shelf: 1 Slot 1 : Port  1
         1.  Port ID             : Shelf 1, Slot 1, Port 1
         2.  Service Mode        : OUT OF SERVICE, MAINTENANCE
             Card Type           : Octal ADSL
             Port Tx Rate        : 0
             Port Rx Rate        : 0
         6.  Port Type           : UNI
             Scrambler           : DISABLE
         8.  Idle Cell Type      : ITU (INVALID CELL)
         9.  Maximum VCCs        : 4096
         10. Maximum VPCs        : 256
         11. Maximum VPI Bits    : 8      Current: 8
         12. Maximum VCI Bits    : 9      Current: 9
         13. Physical Address    : 00-0000:00000000000000000000-000000000000.00
         14. Neighbor Name       :
         15. Neighbor IP Address : 0.0.0.0
         16. PNNI port options
         17. Restore Factory Defaults
         I-ILMI, P-Next Port, S-Next Slot, H-Next Shelf, SELECTION

Summary of Contents for DS3-PSM











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands