manualshive.com logo in svg

ADTRAN DS3-PSM, Installation And Maintenance Practice

Share
Download
ADTRAN DS3-PSM Installation And Maintenance Practice Download Page 110

Total Access 3000 DSLAM DS3 Primary Switch Module Installation and Maintenance Practice

100

 

61181041L3-5A

OAM Loopback Test Screen
The OAM Loopback Test Screen (see 

Figure 53

) is used to perform OAM Loopback testing. The 

OAM Loopback test sends OAM Cells with the loopback indication bit set. The Remote OAM ID 
must be entered to identify at which connecting node the loopback should occur. Upon the 
Remote receiving the OAM Loopback cell, the remote will respond with an OAM cell with the 
loopback indication bit cleared. For the DS3-PSM to properly respond to OAM loopbacks 
directed at it, the OAM ID of the DS3-PSM should be set to a value other than all “6A”s. When 
a DS3-PSM has the OAM ID set to the default of all “6A”s, then OAM loopbacks are ignored.

Figure 53.  OAM Loopback Test Screen

The OAM Loopback Test Screen options are shown in 

Table 61

.

Table 61.  OAM Loopback Test Screen Options

Option 

Description

Function

INDEX

This field displays the index number assigned to the VC/VP.

STATUS

This field displays the status of the VC/VP as Enabled or Disabled.

TYPE

This field displays the type as either PVC or PVP.

SRV-CL

This field displays the Service Class assigned to the PVC (defined by the traffic 
descriptor).

Endpoint 1 (Top Level)

SH/SL/PO

This field displays the shelf/slot/port location of the VC/VP Endpoint 1.

VPI

This field displays the current VPI value of the VC/VP Endpoint 1.

VCI

This field displays the current VCI value of the VC/VP Endpoint 1.

Shelf: 1 Slot: B               Total Access System                    MM/DD/YY HH:MM
                                                                ONLINE
                           OAM LOOPBACK TEST SCREEN
                  VC/VP Name: _InbandPVC
                             ENDPOINT 1       <->      ENDPOINT 2
     INDEX STATUS   TYPE SH/SL/PO  VPI  VCI   <->  SH/SL/PO  VPI  VCI   SRV-CL
         1 ENABLED  PVC  MGMT PORT 0    32    <->  DS3  PORT 0    33    nrtVBR
       1.  Endpoint 1 Remote OAM ID : FF:FFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
       2.  Endpoint 2 Remote OAM ID : FF:FFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
       3.  TYPE OF OAM CELL: SEGMENT
       4.  SEND FROM ENDPOINT1 (toward endpoint 1 eqpt.)
       5.  SEND FROM ENDPOINT2 (toward endpoint 2 eqpt.)
       6.  RESET OAM LOOPBACK STATS
              --------------------ENDPOINT1--------------------
       OAM Tx LoopBack Req  : 0          OAM Tx LoopBack Rsp  : 0
       OAM Rx LoopBack Req  : 0          OAM Rx LoopBack Rsp  : 0
       OAM LoopBack Passed  : 0          OAM LoopBack Failed  : 0

              --------------------ENDPOINT2--------------------
       OAM Tx LoopBack Req  : 0          OAM Tx LoopBack Rsp  : 0
       OAM Rx LoopBack Req  : 0          OAM Rx LoopBack Rsp  : 0
       OAM LoopBack Passed  : 0          OAM LoopBack Failed  : 0

         Selection:

Summary of Contents for DS3-PSM











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands