manualshive.com logo in svg

ADTRAN DS3-PSM, Installation And Maintenance Practice

Share
Download
ADTRAN DS3-PSM Installation And Maintenance Practice Download Page 120

Total Access 3000 DSLAM DS3 Primary Switch Module Installation and Maintenance Practice

110

 

61181041L3-5A

DS3 CSM Performance Monitoring Menu

The DS3 CSM Performance Monitoring menu (see 

Figure 57

) is used to access submenus to 

view DS3 performance monitoring data in daily, 24-hour, or 15 minute increments.

Figure 57.  DS3 CSM Performance Monitoring Menu

The DS3 CSM Performance Monitoring menu options are shown in 

Table 66

.

Table 66.  DS3 CSM Performance Monitoring Menu Options

Option 

Description

Function

1

Daily

This option displays the 

“DS3 CSM Daily Menu” 

on 

page 111.

2

Far-End Daily

This option displays the 

“DS3 CSM Far-End Daily Menu” 

on 

page 113.

3

Total 24 Hour Period

This option displays the Total 24 Hour Period screen.

4

Total 24 Hour Period Far-
End

This option displays the Total 24 Hour Period Far-End 
screen.

5

Qrtr-Hourly

This option displays the DS3 CSM Qrtr-Hourly screen.

6

Far-End Qrtr-Hourly

This option displays the DS3 CSM Far-End Qrtr-Hourly 
screen.

7

Reset Performance 
Registers

This option is used to reset the performance registers to N/A 
(not available) except for the current interval which is set to 
zero.

Shelf: 1 Slot: B               Total Access System                    MM/DD/YY HH:MM
                                                                ONLINE

                            DS3 CSM Performance Monitoring

                           1.  Daily
                           2.  Far-End Daily

                           3.  Total 24 Hour Period
                           4.  Total 24 Hour Period Far-End

                           5.  Qrtr-Hourly
                           6.  Far-End Qrtr-Hourly

                           7.  Reset Performance Registers

                           Selection:

                            '?' - System Help Screen

Summary of Contents for DS3-PSM











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands