manualshive.com logo in svg

ADTRAN DS3-PSM, Installation And Maintenance Practice

Share
Download
ADTRAN DS3-PSM Installation And Maintenance Practice Download Page 105

Menu Trees

61181041L3-5A

 95

DS3 Loopbacks Menu
The DS3 Loopbacks menu (see 

Figure 50

) is used to access submenus to perform various DS3 

loopback tests.

Figure 50.  DS3 Loopbacks Menu

The DS3 Loopbacks menu options are shown in 

Table 57

.

Table 57.  DS3 Loopbacks Menu Options

Option 

Description

Function

1

No Loopback

This option is used when not actively testing.

2

Network Payload Loopback

This option is used to perform a Network Payload Loopback 
test. This test sends a loopback toward the network past the 
DS3 Framer.

3

Network Loopback

This option is used to perform a Network Loopback test. This 
test sends a loopback toward the network before the DS3 
Framer.

4

Local Payload Loopback

This option is used to perform a Local Payload Loopback 
test. This test sends a loopback toward the loop ports.

5

Dual Loopback

This option is used to perform a Dual Loopback test. This 
test sends a loopback toward the network and also toward 
the loop ports.

6

LIU Network Loopback

This option is used to perform an LIU Network Loopback 
test. This test sends a loopback toward the network at the 
LIU.

Shelf: 1 Slot: B               Total Access System                    MM/DD/YY HH:MM
                                                                ONLINE

                                   DS3-PSM

                                DS3 Loopbacks

                                1 .  No Loopback
                                2 .  Network Payload Loopback
                                3 .  Network Loopback
                                4 .  Local Payload Loopback
                                5 .  Dual Loopback
                                6 .  LIU Network Loopback
                                7 .  LIU Digital Local Loopback
                                8 .  LIU Analog Local Loopback

                                Selection:

                            '?' - System Help Screen

Summary of Contents for DS3-PSM











































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands