manualshive.com logo in svg

AddPac PassFinder AP2520, User Manual

The AddPac PassFinder AP2520 is a versatile network appliance, perfect for small to medium-sized businesses. Ensure seamless integration with user manuals available for free download from manualshive.com. Get step-by-step instructions and troubleshoot with ease using the comprehensive manual. Empower your network with the AP2520 today.

Share
Download
background image

PassFinder AP2520 VoIP Router/Gateway Operation Manual   

Version 1.10 / Mar. 2002 

AddPac Technology Co., Ltd. 

 

   

          - 

76

 - 

[Example] Added Commands During PAP Configuration (Client)

 

This is when the AP2520 router is used as a PPP CallIn on the client side.   

 

router (config)#interface serial 1

 

☞

 Enters into the interface 

configuration mode. 

router(config-serial1)# encapsulation ppp

 

☞

 Sets the PPP mode.  

router(config-serial1)# ppp authentication pap

 

☞

 Sets  the  PPP 

authentication mode as PAP for the serial 1 interface. 

router(config-serial1)# ppp pap sent-username addpac password 

router1

 

☞

 Sends the user name and the password that were saved in the 

server during PPP connection. 

router(config-serial1)# ppp timeout 100

 

☞

 Sets PPP connection 

negotiation timeout value as 100 seconds. 

router(config-serial1)# end

 

☞

 Exists from the configuration menu. 

router #

  

Serial1 LCP: TIMEOUT 

Serial1 LCP: O CONFREQ id=1 

Serial1 BCP: TIMEOUT 

Serial1 BCP: O  CONFREQ id=1 

Serial0 LCP: TIMEOUT 

Serial0 LCP: O CONFREQ id=1 

Serial0 BCP: TIMEOUT 

Serial0 BCP: O  CONFREQ id=1

 

router # debug ppp packet

 

☞

 Stops PPP packet debugging.

 

 

If the interface of the router is not used    as DHCP, the IP address must be set in 

the corresponding interface. 

 
 
 

Caution 

 

Summary of Contents for PassFinder AP2520

















































































































































































































































































































































































Reviews:

No comments

Related manuals for PassFinder AP2520

ABB ARR600 Quick Start Manual preview
ARR600
Brand: ABB Pages: 4
Banner SureCross DX80 Reference Manual preview
SureCross DX80
Brand: Banner Pages: 96
Yeastar Technology TB200 Installation Manual preview
TB200
Brand: Yeastar Technology Pages: 11
National Instruments WSN-9791 Getting Started Manual preview
WSN-9791
Brand: National Instruments Pages: 15
Juniper SRX3600 Replacing preview
SRX3600
Brand: Juniper Pages: 3
Moeller CM4-505-GV1 Hardware And Engineering preview
CM4-505-GV1
Brand: Moeller Pages: 78
Logic IO RTCU NX-910 Technical Manual preview
RTCU NX-910
Brand: Logic IO Pages: 45
Xorcom CXE2000 Getting Starded Manual preview
CXE2000
Brand: Xorcom Pages: 7
Zipato Zipamini User Manual preview
Zipamini
Brand: Zipato Pages: 36
NETGEAR C6300BD Installation Manual preview
C6300BD
Brand: NETGEAR Pages: 6
ABB 83342 Operating Instructions Manual preview
83342
Brand: ABB Pages: 20
Samson 5007-2 Series Mounting And Operating Instructions preview
5007-2 Series
Brand: Samson Pages: 72
Telco Access 211N Installation Manual preview
Access 211N
Brand: Telco Pages: 4
Siemens CXG3.X200 Manual preview
CXG3.X200
Brand: Siemens Pages: 12
Wieland GW 100 Installation Instruction preview
GW 100
Brand: Wieland Pages: 2
3Com OfficeConnect 3CR856-95 Installation Manual preview
OfficeConnect 3CR856-95
Brand: 3Com Pages: 2
Mi-Light MiBoxer ZB-Box2 Manual preview
MiBoxer ZB-Box2
Brand: Mi-Light Pages: 6
Efento Gateway User Manual preview
Gateway
Brand: Efento Pages: 14

Brands by name

Popular brands

Load more brands