manualshive.com logo in svg

AddPac PassFinder AP2520, User Manual

The AddPac PassFinder AP2520 is a versatile network appliance, perfect for small to medium-sized businesses. Ensure seamless integration with user manuals available for free download from manualshive.com. Get step-by-step instructions and troubleshoot with ease using the comprehensive manual. Empower your network with the AP2520 today.

Share
Download
background image

PassFinder AP2520 VoIP Router/Gateway Operation Manual   

Version 1.10 / Mar. 2002 

AddPac Technology Co., Ltd. 

 

   

          - 

96

 - 

(NBMA) such as frame-relay, disable the split-horizon option.     

 

z

 

show route

 

Checks the routes in the routing table. 

 

z

 

show router

 

Checks the enabled routing process. 

 

z

 

show rip 

 

Checks RIP status of each interface.   

 

z

 

debug rip 

 

Decodes RIP packets exchanged by the router and shows status of RIP 

packets.  

 

[Example] RIP Configuration and Usage 
 

router# config 

router(config)# ip routing

 

☞

 Enables IP routing. 

Router(config)# router rip

 

☞

 Enable the RIP process. 

Router(config)# interface Ethernet 0.0

 

☞

 Enters into a configuration 

mode for the sub-interface 0 of the Ethernet interface 0.  

Router(config-ether0.0)# ip rip send 12

 

☞

Set RIP v1/v2 through the 

corresponding interface.  

Router(config-ether0.0) # ip rip receive 1

 

☞

Receives only RIP v1 

packets among advertise packets, which come through corresponding 

interface. 

Router(config-ether0.0) # ip rip auth-type simple

 

☞

 Set  Simple 

Authentication for RIP information exchange through corresponding 

interface. 

 

Router(config-ether0.0)# ip rip convergence split-horizon

 

☞

In 

RIP Process, this enables Split-Horizon as Convergence Mechanism. 

Router(config-ether0.0)# ip rip convergence poison-revers

 

☞

In 

Summary of Contents for PassFinder AP2520

















































































































































































































































































































































































Reviews:

No comments

Related manuals for PassFinder AP2520

ICP DAS USA GT-541 User Manual preview
GT-541
Brand: ICP DAS USA Pages: 33
3Com PathBuilder S200 Series Manual preview
PathBuilder S200 Series
Brand: 3Com Pages: 31
3Com OfficeConnect 3C855 Frequently Asked Questions preview
OfficeConnect 3C855
Brand: 3Com Pages: 3
3Com OfficeConnect 3C855 Using preview
OfficeConnect 3C855
Brand: 3Com Pages: 4
AudioCodes Mediant 1000 MSBG Cli Reference Manual preview
Mediant 1000 MSBG
Brand: AudioCodes Pages: 160
CYP CLUX-18EU Operation Manual preview
CLUX-18EU
Brand: CYP Pages: 12
C2G Trulink Media gateway W02 Installation Manual preview
Trulink Media gateway W02
Brand: C2G Pages: 23
YX Wireless TELULINK User Manual preview
TELULINK
Brand: YX Wireless Pages: 12
Sangoma Netborder SS7 Quick Start Manual preview
Netborder SS7
Brand: Sangoma Pages: 4
IC nexus VPC100 Series Quick Start Manuals preview
VPC100 Series
Brand: IC nexus Pages: 36
ABB 83342 Operating Instructions Manual preview
83342
Brand: ABB Pages: 20
Xentino HSP500 User Manual preview
HSP500
Brand: Xentino Pages: 126
Popp 011801 Manual preview
011801
Brand: Popp Pages: 13
Kiloview RMG-300 Quick Start Manual preview
RMG-300
Brand: Kiloview Pages: 11
King Pigeon BL280 User Manual preview
BL280
Brand: King Pigeon Pages: 52
King Pigeon S175 User Manual preview
S175
Brand: King Pigeon Pages: 55
Schwaiger HA102 User Manual preview
HA102
Brand: Schwaiger Pages: 24
RAB Lightcloud LCGATEWAY Manual preview
Lightcloud LCGATEWAY
Brand: RAB Pages: 67

Brands by name

Popular brands

Load more brands