background image

PassFinder AP2520 VoIP Router/Gateway Operation Manual   

Version 1.10 / Mar. 2002 

AddPac Technology Co., Ltd. 

 

   

          - 

3

 - 

4.2.3.

 

Commands of the Configuration Mode..................................................................48

 

4.2.3.1.

 

Global Configuration(config) Commands......................................................48

 

4.2.3.2.

 

Commands of the Interface Configuration Mode 1 .....................................50

 

4.2.3.3.

 

Commands of the Interface Configuration Mode 2 (IP Configuration 

Mode) 51

 

4.3.

 

Starting Gateway Configuration....................................................................................52

 

4.4.

 

Ethernet Configuration ...................................................................................................53

 

4.4.1.

 

Ethernet basic configuration .....................................................................................53

 

4.4.2.

 

PPPoE Configuration ...................................................................................................57

 

4.5.

 

WAN (Serial) Interface Configuration ...........................................................................66

 

4.5.1.

 

HDLC Configuration ....................................................................................................67

 

4.5.2.

 

PPP Configuration .......................................................................................................70

 

4.5.3.

 

Frame-Relay Configuration........................................................................................79

 

4.6.

 

Routing Configuration ....................................................................................................88

 

4.6.1.

 

Static Routing Configuration .....................................................................................89

 

4.6.2.

 

RIP Configuration.........................................................................................................92

 

4.6.3.

 

OSPF Configuration.....................................................................................................98

 

4.7.

 

Filter (Access-List) Configuration.................................................................................106

 

4.8.

 

NAT(Network Address Translation) Configuration......................................................113

 

4.9.

 

DHCP(Dynamic Host Configuration Protocol) Configuration....................................123

 

4.10.

 

Transparent Bridging Configuration ............................................................................131

 

4.11.

 

SNMP Configuration......................................................................................................136

 

4.12.

 

Gateway Management Command............................................................................141

 

4.12.1.

 

Command in the EXEC Mode .................................................................................141

 

4.12.2.

 

Command in the Global Configuration Mode ....................................................145

 

4.13.

 

Fault Management and Debugging ...........................................................................148

 

4.13.1.

 

Logging Command ..................................................................................................148

 

4.13.2.

 

Show commands.......................................................................................................149

 

4.13.3.

 

Debug Commands ...................................................................................................153

 

4.14.

 

User, Password, Software Image and Configuration File Management ..................155

 

4.14.1.

 

User Registration and Change ................................................................................155

 

4.14.2.

 

Password Recovery...................................................................................................157

 

4.14.3.

 

Software Image Upgrade and Backup .................................................................160

 

4.14.4.

 

Configuration File

 Backup 

 Restore ..............................................................163

 

Chapter 5

 

Voice Configuration and Command ............................................165

 

5.1.

 

Voice Technologies and Concepts ............................................................................165

 

5.1.1.

 

Voice Over IP .............................................................................................................165

 

5.1.2.

 

Codecs and MOS(Mean Opinion Score)..............................................................166

 

Summary of Contents for PassFinder AP2520

















































































































































































































































































































































































Reviews: