AddPac PassFinder AP2520 User Manual Download

Page: 104 / 368

PassFinder AP2520 VoIP Router/Gateway Operation Manual

Version 1.10 / Mar. 2002

AddPac Technology Co., Ltd.

104

[Example] OSPF Configuration and Usage

Router# config

router(config)# ip routing

☞

Enables IP routing.

router(config)# interface Ethernet 0 0

☞

Enters into a configuration

mode for the sub-interface 0 of the Ethernet interface 0.

router(config-ether0.0)# ip

address 130.1.1.1 255.255.255.0

☞

Sets

the IP address as “130.1.1.1/24bit.”

router(config-ether0.0)# ospf enable

☞

Enables the OSPF in the

interface.

router(config-ether0.0-ip)# ospf area-id 10

☞

Makes the Ethernet

interface belong to OSPF Area 10. Through this, the corresponding network

address enters into OSPF Process area 10.

router(config-ether0.0)# ospf priority 10

☞

If DR is selected, sets

Priority 10 for the router to make Nego against the other router.

router(config-ether0.0)# ospf cost 5

☞

Sets that the Cost (metric)

value should be advertised as 5.

router(config-ether0.0)# int serial 0

☞

Enters into the serial 1

interface configuration mode.

router(config-serial0)# ip

address 135.1.1.1 255.255.255.0

☞

Sets

the IP address as “135.1.1.1/24bit.”

router(config-serial0)# ospf enable

☞

Enables OSPF in the interface.

router(config-serial0)# ospf area-id 0

☞

Makes the serial interface

0 belong to OSPF Area 0. Through this, the corresponding network address

enters into OSPF Process area 0.

router(config-serial0)# ospf priority 1

☞

If DR is selected, sets

Priority 1 for this router to make Nego against the other router.

router(config-serial0)# ospf cost 10

☞

Sets that the Cost (metric)

value for the interface should be advertised as 10.

router(config-serial0)# ospf network broadcast

☞

Sets that the

features for this interface are broadcasted.

router(config-serial0)# exit

☞

Returns to the previous configuration

mode.

router(config)# router ospf

☞

Enables the OSPF process. From this

point, the OSFP process operates. The user shall set this command after

Summary of Contents for PassFinder AP2520

















































































































































































































































































































































































Search results

Summary of Contents for PassFinder AP2520

Reviews:

Related manuals for PassFinder AP2520

Brands by name

Popular brands

AddPac PassFinder AP2520, User Manual

Search results

Summary of Contents for PassFinder AP2520

Reviews:

Related manuals for PassFinder AP2520

Brands by name

Popular brands