SERIES IP511 INDUSTRIAL I/O PACK ISOLATED QUAD EIA/TIA-422B COMMUNICATION MODULE
___________________________________________________________________________________________
- 23 -
CABLE: MODEL 5029-900
Type: Model 5029-900 APC8600 High-Density Cable: A 36-inch long
interface cable that mates the high-density (25mil pitch) 50-pin I/O
connectors of the APC8600 PC/AT ISAbus carrier board, to the
high density connectors on the APC8600 Termination Panels
(described below).
Application: Used with the APC8600 PC carrier and termination panel.
It mates the high-density (25mil pitch) 50-pin I/O connectors of the
APC8600 PC/AT ISAbus carrier board, to the high density
connectors on the APC8600 Termination Panel (described below).
Length: 36-inches
Cable: 50-wire flat ribbon cable, 28 gage, Non-Shielded, T&B/Ansley
Part 135-050 or equivalent.
Headers: 50-pin, high-density, 25-mil pitch, female header. Header-
T&B Ansley Part 311-050302 or equivalent.
Keying: Headers at both ends have polarizing key to prevent improper
installation.
Shipping Weight: 1.0 pound (0.5Kg) packaged.
TERMINATION PANEL: MODEL 5025-552
Type: Termination Panel For AVME9630/9660 Boards
Application: To connect field I/O signals to the Industrial I/O Pack
(IP).
Termination Panel:
Acromag Part 4001-040 (Phoenix
Contact Type FLKM 50). The 5025-552 termination panel
facilitates the connection of up to 50 field I/O signals and connects
to the AVME9630/9660 3U/6U non-intelligent carrier boards (A-D
connectors only) via a flat ribbon cable (Model 5025-550-x or 5025-
551-x). The A-D connectors on the carrier board connect the field
I/O signals to the P2 connector on each of the Industrial I/O Pack
modules. Field signals are accessed via screw terminal strips.
The terminal strip markings on the termination panel (1-50)
correspond to P2 (pins 1-50) on the Industrial I/O Pack (IP). Each
Industrial I/O Pack (IP) has its own unique P2 pin assignments.
Refer to the IP module manual for correct wiring connections to the
termination panel.
Schematic and Physical Attributes: See Drawing 4501-464.
Field Wiring: 50-position terminal blocks with screw clamps. Wire
range 12 to 26 AWG.
Connections to AVME9630/9660: P1, 50-pin male header with strain
relief ejectors. Use Acromag 5025-550-x or 5025-551-x cable to
connect panel to VME board. Keep cable as short as possible to
reduce noise and power loss.
Mounting: Termination panel is snapped on the DIN mounting rail.
Printed Circuit Board: Military grade FR-4 epoxy glass circuit board,
0.063 inches thick.
Operating Temperature: -40
°
C to +100
°
C.
Storage Temperature: -40
°
C to +100
°
C.
Shipping Weight: 1.25 pounds (0.6kg) packaged.
TERMINATION PANEL: MODEL 5029-910
Type: Screw-Terminal Termination Panel For Acromag APC8600
PC/AT ISAbus Carrier Boards.
Application: This panel converts the high-density ribbon-cable
connectors coming from the APC8600 carrier board (Acromag
cable Model 5029-900) to screw terminals, for direct-wired
interfaces. This panel facilitates the connection of up to 50 field I/O
signals and connects to the APC8600 PC/AT ISAbus carrier board
via high-density (25-mil pitch) flat ribbon cable and connectors (see
cable Model 5029-900). The A & B connectors on the carrier board
connect the field I/O signals to the P2 connector on each of the
Industrial I/O Pack modules. Field signals are accessed via screw
terminal strips. Each Industrial I/O Pack (IP) has its own unique
P2 pin assignments. Refer to the IP module manual for correct
wiring connections to the termination panel.
Field Wiring: 50-position terminal blocks with screw clamps. Wire
range 12 to 26 AWG.
Connections to APC8600: P1, 50-pin, high-density male header with
strain relief.
Mounting: Termination Panel includes mounting holes.
Printed Circuit Board: Military grade FR-4 epoxy glass circuit board,
0.063 inches thick.
Operating Temperature: -40
°
C to +85
°
C.
Storage Temperature: -55
°
C to +125
°
C.
Shipping Weight: 1.25 pounds (0.6kg) packaged.
TRANSITION MODULE: MODEL TRANS-GP
Type: Transition module for AVME9630/9660 boards.
Application: To repeat field I/O signals of IP modules A through D for
rear exit from VME card cages. This module is available for use in
card cages which provide rear exit for I/O connections via transition
modules (transition modules can only be used in card cages
specifically designed for them). It is a double-height (6U), single-
slot module with front panel hardware adhering to the VMEbus
mechanical dimensions, except for shorter printed circuit board
depth. Connects to Acromag termination panel 5025-552 from the
rear of the card cage, and to AVME9630/9660 boards within card
cage, via flat 50-pin ribbon cable (cable Model 5025-550-X or 5025-
551-X).
Schematic and Physical Attributes: See Drawing 4501-465.
Field Wiring: 100-pin header (male) connectors (3M 3433-D303 or
equivalent) employing long ejector latches and 30 micron gold in the
mating area (per MIL-G-45204, Type II, Grade C). Connects to
Acromag termination panel 5025-552 from the rear of the card cage
via flat 50-pin ribbon cable (cable Model
5025-550-X or 5025-551-X).
Connections to AVME9630/9660: 50-pin header (male) connectors (3M
3433-1302 or equivalent) employing long ejector latches and 30
micron gold in the mating area (per MIL-G-45204, Type II, Grade
C). Connects to AVME9630/9660 boards within the card cage via
flat 50-pin ribbon cable (cable Model 5025-550-X or 5025-551-X).
Mounting: Transition module is inserted into a 6U-size, single-width
slot at the rear of the VMEbus card cage.
Printed Circuit Board: Six-layer, military-grade FR-4 epoxy glass circuit
board, 0.063 inches thick.
Operating Temperature: -40
°
C to +85
°
C.
Storage Temperature: -55
°
C to +105
°
C.
Shipping Weight: 1.25 pounds (0.6Kg) packaged.
