SERIES IP511 INDUSTRIAL I/O PACK ISOLATED QUAD EIA/TIA-422B COMMUNICATION MODULE
___________________________________________________________________________________________
- 22 -
Termination Resistors...................120
Ω
Termination Resistors are
installed in sockets on board at
receiver inputs only and may be
removed if required (see Drawing
4501-582 for location). Install
termination resistors at the far-
most ends of a network only.
Bias Resistors...............................Bias resistors are not required
since driver (transmitter) is always
enabled (see Drawing 4501-582).
Differential Output Voltage ...........5V Max. (Unloaded); 2V Min.
(RS-422, 50
Ω
load); 1.5V Min.
(RS-485, 27
Ω
load).
Common Mode Output Voltage.....3V Maximum (27
Ω
or 50
Ω
load).
Output Short Circuit Current.........250mA Maximum.
Driver Input to Output Time...........10ns to 50ns, 54
Ω
, 100pF.
Differential Input Threshold.......... -0.2V Minimum, +0.2V Maximum.
Receiver Input Hysteresis.............70mV Typical.
Receiver Input Resistance............12K
Ω
, Minimum.
Receiver Input Current..................1mA Maximum
Receiver Input to Output Time......40ns to 150ns, 54
Ω
, 100pF.
INDUSTRIAL I/O PACK COMPLIANCE
Specification................................This module meets or exceeds all
written Industrial I/O Pack
specifications per revision 0.7.1.
Electrical/Mechanical Interface....Single-Size IP Module.
IP Data Transfer Cycle Types Supported:
Input/Output (IOSel*)............D16 or D08 least significant byte
read/write of data.
ID Read (IDSel*)...................32 x 8 ID PROM read on D0..D7.
Interrupt Select (INTSel*)......8-bit word (D08) read of Scratch
Pad/Interrupt Vector Register.
Access Times (8MHz Clock):
ID PROM Read.....................1 wait state (375ns cycle).
I/O Register Read/Write........2 wait states (500ns cycle).
Interrupt Select Read.............2 wait states (500ns cycle).
APPENDIX
CABLE: MODEL 5025-550-x (Non-Shielded)
MODEL 5025-551-x (Shielded)
Type: Flat Ribbon Cable, 50-wires (female connectors at both ends).
The ‘-x’ suffix designates the length in feet (12 feet maximum).
Choose shielded or unshielded cable according to model number.
The unshielded cable is recommended for digital I/O, while the
shielded cable is recommended for optimum performance with
precision analog I/O applications.
Application: Used to connect a Model 5025-552 termination panel to
the AVME9630/9660 non-intelligent carrier board A-D connectors
(both have 50-pin connectors).
Length: Last field of part number designates length in feet (user-
specified, 12 feet maximum). It is recommended that this length be
kept to a minimum to reduce noise and power loss.
Cable: 50-wire flat ribbon cable, 28 gage. Non-Shielded cable model
uses Acromag Part 2002-211 (3M Type C3365/50 or equivalent).
Shielded cable model uses Acromag Part 2002-261 (3M Type
3476/50 or equivalent).
Headers (Both Ends): 50-pin female header with strain relief.
Header -
Acromag Part 1004-512 (3M Type 3425-6600 or equivalent).
Strain Relief -
Acromag Part 1004-534 (3M Type 3448-3050 or
equivalent).
Keying: Headers at both ends have polarizing key to prevent improper
installation.
Schematic and Physical Attributes: For Non-Shielded cable model, see
Drawing 4501-462. For Shielded cable model, see Drawing 4501-
463.
Shipping Weight: 1.0 pound (0.5Kg) packaged.
CABLE: MODEL 5029-943
Type: Model 5029-943 IP500 Communication Cable: A five foot long,
flat 50-pin cable with a female connector on one end (for
connection to AVME9630/9660 or other compatible carrier boards)
and four DE-9P connectors (serial ports) on the other end.
Application: Used to connect up to four DB-9 serial ports to
AVME9630/9660 non-intelligent carrier board A-D connectors. It is
used primarily with Acromag Model IP500, IP511, IP502, & IP512
serial communication modules.
Length: 5 feet.
Cable: 50-wire flat ribbon cable, 28 gage. Non-Shielded cable model
uses Acromag Part 2002-211 (3M Type C3365/50 or equivalent).
Headers: 50-pin female header with strain relief.
Header -
Acromag
Part 1004-512 (3M Type 3425-6600 or equivalent).
Strain Relief -
Acromag Part 1004-534 (3M Type 3448-3050 or equivalent).
Port Connectors: Four DE-9P (9-pin, D-SUB, Male) connectors with
strain relief (3M connector U89809-9000 with 3448-8D09A strain
relief, or equivalent).
Keying: 50-pin Header at one end has polarizing key to prevent
improper installation.
Schematic and Physical Attributes: See Drawing 4501-580.
Shipping Weight: 1.0 pound (0.5Kg) packaged.
