ABB OmniCore C30 Product Manual Download Page 520

Page: 520 / 606

Location of LEDs

xx1700001886

Detailed working procedure

Note

Action

See

Operating manual - OmniCore

Try resetting the FlexPendant using the reset
button located next to the USB port.

If it is not connected, repair the
connection and go to step six.

Check that the FlexPendant cable is correctly
connected to the controller through the HMI signal
connector, X4.

Check the pins in the connector.
If it is ok, go to the next step.

For more details about the LEDs,
see

Troubleshooting the robot sig-

nal exchange proxy on page 555

•

If the LEDs are not green,
see

Troubleshooting the ro-

bot signal exchange proxy
on page 555

•

If they are ok, go to the next
step.

Check the LED PC and LED HMI, they should be
green.

•

If damage is found, replace
the FlexPendant cable and
go to step six.

•

If it is ok, go to the next
step.

Check the FlexPendant cable for any damage.

•

If it is not ok, repair the con-
nection and go to step six.

•

If it is ok, go to the next
step.

Check that the connection from the robot signal
exchange proxy to the HMI signal connector is
ok, K2.X9, 13 - X4.

Continues on next page

520

Product manual - OmniCore C30

3HAC060860-001 Revision: P

6 Troubleshooting

6.2.5 Problem starting or connecting the FlexPendant

Continued

Summary of Contents for OmniCore C30






























































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore C30

Reviews:

Brands by name

Popular brands

ABB OmniCore C30, Product Manual

Search results

Summary of Contents for OmniCore C30

Reviews:

Brands by name

Popular brands