ABB OmniCore C30 Product Manual Download Page 486

Page: 486 / 606

Note/Illustration

Action

For the robot signal exchange proxy:

•

K2.X8 - A2.X6

•

(option): K2.X2 - K4.X8, A2.X1

•

K2.X12 - A2.K3.X6, A2.K3.X7

•

K2.X10 - A1.X13

•

K2.X21 - TempSensor

•

K2.X4 - A1.X9

•

K2.X3 - K6.X1, A2.K3.X1, K5.1.X4,
K7.X1

•

K2.X1 - T2.X2

•

K2.X1 - X107

•

K2.X17 - G2.X1, G1.X2

•

K2.X6, K2.X11 - A1.X2

•

K2.X7, K2.X22 - Harn. LV robot
power

•

K2.X9 & X13 - FlexPendant

For the Ethernet extension switch (op-
tion):

•

K2.X2 - K4.X8, A2.X1

•

A2.X4 - K4.X6

Note

When Ethernet extension switch
is selected, connect and discon-
nect the connector A2.X4) to/from
K4.X6.

•

Harness adapter - A2.X4/K4.X7.

Note

When Ethernet extension switch
is selected, connect and discon-
nect the adapter cable (Adapter -
A2.X4/K4.X7) to/from K4.X7.

For the connected services gateway:

•

K7.X1 - K2.X3

•

K7.X2 - A2.X5

Note

The connector K7.X2 is locked;
grab the connector, push it in to
release it and then remove the
connector.

Continues on next page

486

Product manual - OmniCore C30

3HAC060860-001 Revision: P

5 Repair

5.3.7 Replacing the IP20 power outlet connector

Continued

Summary of Contents for OmniCore C30






























































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore C30

Reviews:

Related manuals for OmniCore C30

Brands by name

Popular brands

ABB OmniCore C30, Product Manual

Search results

Summary of Contents for OmniCore C30

Reviews:

Related manuals for OmniCore C30

Brands by name

Popular brands