manualshive.com logo in svg

ABB OmniCore C30, Product Manual

Share
Download
ABB OmniCore C30 Product Manual Download Page 363

Note/Illustration

Action

Reconnect:

•

A1.X13 - K2.X10

•

A1.X9 - K2.X4

•

A1.X4 - T4.X5

35

•

A1.X4 - X1

36

•

A1.X5 - T4.X1

•

A1.X12 - T4.X3

•

A1.X1 - Incoming mains (X0)

•

A1.X6 - T2.X1

37

•

A1.X6 - X107

38

•

(Option) A1.X7 - T5.X1

4

Put the main harness in place and secure
it with the velcro straps.

5

Refitting the axis computer to the frame

Note/Illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

page 31

.

1

Location of wrist strap button:

xx1800000683

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

ESD on page 47

.

2

Reconnect:

•

K6.X4, K6.X5 - SMB.

3

35 Not available for CRB 15000 controller.
36 Only used for CRB 15000 controller.
37 Not available for CRB 15000 controller.
38 Only used for CRB 15000 controller.

Continues on next page

Product manual - OmniCore C30

363

3HAC060860-001 Revision: P

© Copyright 2019-2022 ABB. All rights reserved.

5 Repair

5.2.10 Replacing the power unit

Continued

Summary of Contents for OmniCore C30































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands