manualshive.com logo in svg

ABB OmniCore C30, Product Manual

Share
Download
ABB OmniCore C30 Product Manual Download Page 487

Note/Illustration

Action

For the main computer:

•

K2.X8 - A2.X6

•

K2.X2 - K4.X8, A2.X1

•

K2.X12 - A2.K3.X6, A2.K3.X7

•

A2.X9 - K6.X2

53

•

A2.X9 - X1

54

•

A2.X5 - K7.X2

•

(Option) A2.K1 - X17

Note

This cable is available when the
fieldbus master and DeviceNet
harness are installed.

•

(Option) A2.X4 - K4.X6

Note

When Ethernet extension switch
is selected, connect and discon-
nect the connector A2.X4) to/from
K4.X6.

•

(Option) Harness adapter -
A2.X4/K4.X7

Note

When Ethernet extension switch
is selected, connect and discon-
nect the adapter cable (Adapter -
A2.X4/K4.X7) to/from K4.X7.
When Ethernet extension unit slot
cover is selected, connect and
disconnect the adapter cable (Ad-
apter - A2.X4/K4.X7) to/from
A2.X4.

For the digital base (option):

•

K5.1.X4 - K2.X3

•

K5.1.X5 - Harness adapter

i

For connected services gateway wired, there is no power cable.

Refitting the axis computer to the frame

Note/Illustration

Action

DANGER

Before doing any work inside the cabinet,
disconnect the mains power. For more
information, see

Electrical safety on

page 31

.

1

Continues on next page

Product manual - OmniCore C30

487

3HAC060860-001 Revision: P

© Copyright 2019-2022 ABB. All rights reserved.

5 Repair

5.3.7 Replacing the IP20 power outlet connector

Continued

Summary of Contents for OmniCore C30































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands