manualshive.com logo in svg

ABB OmniCore C30, Product Manual

Share
Download
ABB OmniCore C30 Product Manual Download Page 311

Note/Illustration

Action

Location of wrist strap button:

xx1800000683

ELECTROSTATIC DISCHARGE
(ESD)

The unit is sensitive to ESD. Before
handling the unit read the safety inform-
ation in section

The unit is sensitive to

ESD on page 47

.

2

xx1800000938

Connect the adapter cable to the digital
base.

•

K5.1.X5 - Harness adapter

Stick the other connector onto the side
of the digital base with the self-adhesive
part.

3

Connect the connectors between the
adapter cable (K5.1.X5 - Adapter) and
the adaptor cable (Adaptor -
A2.X4/K4.X7).

Note

If the Ethernet extension switch is in-
stalled, connect and disconnect the ad-
apter cable (A2.X4/K4.X7) to/from K4.X7.
If the Ethernet extension unit slot cover
is installed, connect and disconnect the
adapter cable (A2.X4/K4.X7) to/from
A2.X4.

4

Continues on next page

Product manual - OmniCore C30

311

3HAC060860-001 Revision: P

© Copyright 2019-2022 ABB. All rights reserved.

5 Repair

5.2.7 Replacing the scalable I/O unit

Continued

Summary of Contents for OmniCore C30































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands