Home
/
ABB
/
ACS180
/
Firmware Manual

ABB ACS180, Firmware Manual, Page: 296 / 392

Share

Page: 296 / 392

ABB ACS180 Firmware Manual Download Page 296

296 Parameters

Advanced

Advanced ID run.
Guarantees the best possible control accuracy. The ID run
takes a very long time to complete. This mode should be
selected when top performance is needed across the
whole operating area.

Note:

The driven machinery must be de-coupled from the

motor because of high torque and speed transients that
are applied.

WARNING!

The motor may run at up to the

maximum (positive) and minimum (negative)
allowed speed during the ID run. Several

accelerations and decelerations are done. The maximum
torque, current and speed allowed by the limit parameters
may be utilized. ENSURE THAT IT IS SAFE TO RUN THE
MOTOR BEFORE PERFORMING THE ID RUN!

6

Adaptive

The drive makes a Standstill ID run first. After that, the
motor parameters will be refined during the normal
operation to achieve more optimal performance. After the
motor model adaptation process is complete, parameter

will be changed from

to

8

Last ID run performed

Shows the type of ID run that was performed last.

None

No ID run has been performed.

0

Normal

ID run.

1

Reduced

ID run.

2

Standstill

ID run.

3

Advanced

ID run.

6

Adaptive

ID run.

Motor polepairs
calculated

Calculated number of pole pairs in the motor.

0

0…1000

Number of pole pairs.

1 = 1

Motor phase order

Switches the rotation direction of motor. This parameter
can be used if the motor turns in the wrong direction (for
example, because of the wrong phase order in the motor
cable), and correcting the cabling is considered
impractical.

Notes:

• Changing this parameter does not affect speed

reference polarities, so positive speed reference will
rotate the motor forward. The phase order selection
just ensures that “forward” is in fact the correct
direction.

U V W

Normal.

0

U W V

Reversed rotation direction.

1

No.

Name/Value

Description

Default
FbEq 16

ACS180 FW.book Page 296 Tuesday, March 9, 2021 2:25 PM

«
...
294
295
296
297
298
...
»

Summary of Contents for ACS180









































































































































































































































































































































































































Reviews:

No comments