3Com VCX V7000 Page 463 Installation Manual Download

Page: 463 / 488

Replacing a Disk (Branch Office)

461

Enter the site ID for the branch office.

Replace the failed disk on the branch office server.

Remove power from the down server.

Remove the failed disk.

Install the replacement disk.

Apply power to the server.

Press the start button on the front panel.

root

and configure networking parameters on the down server

by entering this command:

vcx-config-network --wizard

Follow the instructions in

“Configuring a Branch Office IP Telephony and

Messaging Server”

Chapter 2

If necessary, upgrade the software on the down server to match the
software version on the other servers in the VCX system.

Compare the software version on the down server to the software
version on another VCX server.

On the down server and the other server, enter this command:

vcx-showversion

If the down server is running an earlier software version than the other
branch office server, download the appropriate software upgrade file
to the

/opt/installtemp

directory on the down server.

The location of the software upgrade file depends on 3Com’s service
delivery methods and on the customer network configuration.

Software upgrade file names begin with the software version and end in
a

.tar

extension (for example: vcx-all-6.0.2c.tar). The examples in this

section assume that you need to upgrade to VCX 6.0.2c.

Install the software upgrade file using these commands:

cd /opt/installtemp

tar xvf vcx-all-6.0.2c

cd upgrade-6.0.2c

./install-upgrade

Switch to the upgraded version of the software using this command:

vcx-switchversion --manual 6.0.2c

Summary of Contents for VCX V7000









































































































































































































































































































































































































































































































Search results

Summary of Contents for VCX V7000

Reviews:

Related manuals for VCX V7000

Brands by name

Popular brands

3Com VCX V7000, Installation Manual

Search results

Summary of Contents for VCX V7000

Reviews:

Related manuals for VCX V7000

Brands by name

Popular brands