Zontes ZT125-GK Скачать руководство пользователя страница 66

Страница: 66 / 81

9-FUEL TANK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1250205-043093 GB70.1M8×55

（

color zinc

）

1251900-028093

Fuel tank flat pad φ9×φ37.5×2 (environmental color)

1244100-020000 ZT250

－

S tank pressure glue

KD150-GK fuel tank assembly

KD150-GK fuel tank sticker

1224200-066000 ZT310PKE External antenna mount

1241200-044000 KD150-U fuel tank liner limit glue

1244100-053000 ZT250

－

S fuel tank gasket

1274100-080000 ZT250

－

R fixed cushion block

Fig.1 FUEL TANK

COMPONENT

Fuel tank component

PROCEDURE

●

Fuel tank component

Short press "FUEL" button to open the fuel tank cover.Do not close it during the subsequent disassembly.If

you

accidentally close it, you can find the fuel tank lock plug near the colloid battery. After connecting, re-

open the fuel tank

cover.Press the "SEAT" button briefly to open the electronic cushion lock,take off the seat

cushion. Follow the steps for

removing the side cover to remove the left and right side covers,refer to "8-

SURROUNDING COMPONENT" to remove the

front grille.

Use 6# inner hexagon to remove 2 bolts (1),take off the fuel tank flat pad

⑵

and remove the rubber (3).

Clamp the circlip of the carbon canister adsorption tube

①

with pliers and pull it out.Unplug the fuel tank lock

plugs

②

Place an oil pan on the left side of the throttle valve body, press down the buckle at the joint of the

high-pressure oil pipe

③

and the injector, and then pull it out.

Lift the rear part of the fuel tank assembly and pull out the fuel pump plug

④

,Note that the buckle of this plug

is on the inside and cannot be removed forcibly.

Grab the head of the fuel tank assembly with one hand and pull it back, and with the other hand, grab the rear

part and lift it up and shake it left and right. Remove the fuel tank assembly from the bike and place it.remove

the fuel tank gasket

⑻

,fixed cushion block

⑼

Pull off the buckle by arrow

⑤

and

⑥

,remove the cables

⑦

on the PKE external antenna mount

⑹

.After

slightly heating with a heat gun, tear off the double-sided tape and clean the residual glue.

Remove the fuel tank liner limit glue

⑺

CAUTION:

●

The parts should be protected during the disassembly process to prevent damage to the paint surface.

●

When removing the buckle, pay attention to the strength to prevent damage to the buckle.

●

When removing the high-pressure oil pipe, be sure to wait until the engine and muffler are completely cooled

before operating to prevent accidental ignition of the fuel and cause fire.

●

Fireworks, answering or dialing should be strictly prohibited near the car-breaking site to prevent accidents.

●

A small amount of fuel leakage is required when the high-pressure oil pipe sub-assembly is pulled out,

andthe

fuel should be prevented from dripping to the outside of the engine or the muffler.

●

It is recommended to use the oil pump to pump out the fuel or consume the fuel before disassembling the

tank

assembly.

Содержание ZT125-GK


















































































Результаты поиска

Содержание ZT125-GK

Отзывы:

Похожие инструкции для ZT125-GK

Бренды по названию

Популярные бренды

Zontes ZT125-GK, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-GK

Отзывы:

Похожие инструкции для ZT125-GK

Бренды по названию

Популярные бренды