Zontes ZT125-GK Скачать руководство пользователя страница 50

Страница: 50 / 81

7-FRONT FORK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1221200-115000 KD150-G1 turn light decorative cover (set)

4041201-384051 KD150-GK right head cover(dark gray matte)

KD150-G1 matte black headlight badge

1170300-064000 HJ125

－

K front right turn signal light

1221200-122000 KD150

－

GK Right turn signal bracket

1251100-101000 Non-standard bolt M6×12 (304 stainless steel)

1274100-057095

Flanging bushing φ6.2×φ8.4×3.5

＋

φ14×1.5

1244100-052000 Buffer rubber of flanging bushing

（

φ8.5×φ14×1

）

1221200-121000 KD150

－

GK left turn signal bracket

1170300-063000 HJ125

－

K front left turn signal light

1251300-063093 Plywood M6×11×15

（

color zinc

）

4041201-383051 KD150-GK left head cover(dark gray matte)

1251100-102000 Non-standard bolt M6×16

（

304 stainless steel

）

1251700-059093

Flanging bushingφ6.4×φ9×8

＋

φ18×2

1240400-007000 HJ125

－

3 battery holder buffer aprons

1020212-100000 KD150

－

G1 headlight upper bracket

4021200-034021 KD150-G1 headlight lower bracket (matte black )

1274100-018000 Anti-hot plate sleeve, muffler

1224200-008000 ZT310

－

R cable plastic staple

Fig.12 FRONT FORK

COMPONENT

PROCEDURE:

●

Left and right turn signal components

Use a Phillips screwdriver to remove the screws on the turn signal decorative cover

⑴

, and remove the turn signal

decorative cover

⑴

. Grasp the left (right) turn signal and use a 17# open-end wrench to remove the nut that comes with the

turn signal, remove the spring washer and gasket that comes with it, and then remove the turn signal.

●

Left and right turn signal bracket assembly

Remove the bolt

⑹

with 4# inner hexagon, take out the flange bushing

⑺

, cushion rubber

⑻

,bushing

⒅

, and disassemble

the left turn signal bracket

⑼

, right turn signal bracket

⑸

, left head cover

⑿

, right head cover

⑵

. Remove the splints

⑾

the left hood

⑿

and right hood

⑵

●

Headlight upper bracket

Remove bolt

⒀

with 4# inner hexagon, remove flange bushing

⒁

and battery holder buffer aprons

⒂

,remove the cable

plastic staple

⒆

and take out headlight upper bracket

⒃

●

Bracket under headlight

Remove the 2 bolts

⑹

with 4# inner hexagon, and remove the headlight bracket

⒄

CAUTION:

●

The head unit should be supported during the disassembly process and protective measures should be taken toprevent

scratching the lamp cover or paint surface.

Head and headlights component 2

Содержание ZT125-GK


















































































Результаты поиска

Содержание ZT125-GK

Отзывы:

Похожие инструкции для ZT125-GK

Бренды по названию

Популярные бренды

Zontes ZT125-GK, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-GK

Отзывы:

Похожие инструкции для ZT125-GK

Бренды по названию

Популярные бренды