Zontes ZT125-GK Скачать руководство пользователя страница 18

Страница: 18 / 81

3-INTAKE SYSTEM COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1251112-001093 M6×16 Hexagon flange bolts (color zinc)

1050956-010000 KD150-G1 EFI High Pressure Tubing Sub-assembly

1051468-007000 31.8×2 fluorine rubber O-ring

1051356-010000

Φ45×10 pipe clamp assembly

1050956-021000 ZT29 Throttle body assembly

1050968-003000 EV14 injector G06

1050968-002000 ZT1P58MJ injector holder

1251100-061093 M6×22 Hex flang bolt thread level 8.8 (color Zinc)

1050961-003000 External intake air pressure

sensor

1050956-025000 KD150Fixed bracket for external intake pressure sensor

CAUTION

●

First it need to remove the cushion,side cover,oil tank outside cover and liner,rear shock absorber

and electrical

device box etc.

●

When removing the high pressure oil pipe,It is sure to operate until the engine and muffler are

completely cooled.

●

Fireworks, answering or dialing should be strictly prohibited near the car-breaking site to prevent

accidents.

PROCEDURE:

●

High-pressure oil pipe

Press the anti-trip buckle on the high-pressure fuel pipe

⑵

and then connect the oil pan to contain the

remaining fuel. Be

careful not to let the fuel drip onto the bike body.

●

Throttle valve body assembly

Unplug the connector of the throttle valve body, remove the throttle cable and use an 8# wrench to remove
the 2 bolts (1)

Remove the throttle valve body assembly.

Remove the O-ring

⑶

, check carefully for damage before reinstalling.

Remove theconnection hose

⒀

at the A-end.

Use 8# wrench to remove the bolt

⑼

,take off the

External intake air pressure sensor component,injector

holder

⑻

and

injector

⑺

After loosening the clamp

⑸

, remove the throttle valve body assembly

⑹

and intake manifold assembly

⑷

and then

remove the clamp

⑸

●

External intake air pressure sensor

Using screwdriver for cruciform head remove the bolt

⑽

,take off the sensor

⑾

and support

⑿

,then remove

the connection

hose

⒀

ZT158M Intake pipe assembly (with intake pressure

sensor)

1050956-022000

Fig.2 INDUCTION

SYSTEM COMPONENT

Throttle valve body component

Intake pressure sensor connection hose(φ3.5×φ7.5×

L38.5)

GB9074.13 Hexagon cross groove spring,flat cushion

combination bolt M5×20

1250106-112000

Содержание ZT125-GK


















































































Результаты поиска

Содержание ZT125-GK

Отзывы:

Похожие инструкции для ZT125-GK

Бренды по названию

Популярные бренды

Zontes ZT125-GK, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-GK

Отзывы:

Похожие инструкции для ZT125-GK

Бренды по названию

Популярные бренды