Zontes ZT125-GK Скачать руководство пользователя страница 69

Страница: 69 / 81

9-FUEL TANK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1274100-090000 ZT250

－

S fuel tank cover rotating shaft

1224100-014000 ZT250

－

S fuel tank cover rotary damping

1274100-021000 ZT250

－

S fuel tank cover rotating bracket

4041201-382051 KD150

－

GK fuel tank cover

1260100-255000 ZT250

－

S torsion spring of tank outer cover rotating

shaft

ZT310

－

T storage box cover rotating shaft limit circlip

1260100-215000

PROCEDURE:

●

Fuel tank cover assembly

Remove the retaining spring

⑸

attached to the rotating shaft

⑴

and slowly pull out the rotating shaft. Remove

the torsion spring

⑷

first.

Remove the swivel bracket assembly.
Remove the rotary shaft

⑴

from the tank cover

⑹

Remove the damper

⑵

from the swivel bracket

⑶

CAUTION:

●

The parts should be protected during the disassembly process to prevent damage to the paint surface.

●

Pay attention to the force when removing the buckle to prevent damage to the buckle.

●

When reassembling, note that the torsion spring and damper need to be properly assembled in place.

Fig.4 FUEL TANK

COMPONENT

Oil tank outer cover assembly

Содержание ZT125-GK


















































































Результаты поиска

Содержание ZT125-GK

Отзывы:

Похожие инструкции для ZT125-GK

Бренды по названию

Популярные бренды

Zontes ZT125-GK, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-GK

Отзывы:

Похожие инструкции для ZT125-GK

Бренды по названию

Популярные бренды