Zontes ZT125-GK Скачать руководство пользователя страница 15

Страница: 15 / 81

2-FRAME & ENGINE COMBINATION

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1244100-061000 ZT250 anti-water rubber of frame

1251100-142000 Non-standard hexagon socket bolt M10 × 1.5 × 130

1244300-026000 ZT350-R guard bar anti-drop glue

1244300-028000

O-ring φ11.8×2.65

（

inner diameter×wire diameter

）

1141200-041000 KD150

－

U left Guard Bar

1241200-056000 KD150-U upgraded version of protective rubber

1251112-001093 M6×16 Hexagon flange bolts (color Zinc)

4024200-027000 ZT310-T frame protection bar pressure plate

1141200-042000 KD150

－

U Right Guard Bar

1141200-043000 KD150

－

U Guard bar left inside bracket

1251100-060000 Non-standard bolts M10X1.5X90

（

dacromet

）

1251300-057093 Non-standard nut M10×1.5

（

dacromet

）

65±5N·m

4021200-021000 KD150

－

U guard bar lower bracket

1251100-132003 Non-standard bolt M10×1.5×80

（

dacromet

）

1141200-044000 KD150

－

U Guard bar right inside bracket

1250305-002091 GB6187.1 M8

（

White zinc

）

1250105-042091 GB5789M8 × 75 (level 10.9 / white zinc)

Fig.1 FRAME & ENGINE

COMBINATION

Frame & engine combination 1

CAUTION:

●

Using suitable tools to support the motorcycle, in case of accidents caused by motorcycle falling down. Single

person operating is prohibited.

●

When reinstalling, please press down the lower bracket of the crash bar to the end and then tighten the fasteners.

Assemble the inner crash bar bracket and the lower guard bar bracket first, and then assemble the surrounding.

●

When reassembling the guard bar, install the guard bar protective glue first and then clip it into the groove of the

lower guard bar bracket and then assemble it to the inner crash bar bracket; finally, assemble the guard bar pressure

plate.

PROCEDURE:

●

Frame protection bar pressure plate

Using 8# sleeve remove 4pcs bolts

⑺

,take off the frame protection bar pressure plate

⑻

●

Guard bar component

Take off rubber

⑴

Grasp the left crash bar assembly firmly, and use 8# inner hexagon to remove the hexagon socket bolt

⑵

; take

off the left crash bar assembly and the glue

⑶

and o-ring

⑷

Remove the protective rubber

⑹

from the left crash bar

⑸

Refer to the above steps to remove the right crash bar

⑼

●

Lower bracket

First remove the seat cushion, fuel tank assembly, surrounding assembly and side cover, and then use the 14#
sleeve to fix the head of the bolt

⒁

, then use the 14# sleeve to remove the nut

⑿

, grasp the lower bracket of the

guard

⒀

and then remove the bolt

⒁

after, remove the lower bracket of the guard bar

⒀

●

Crash car assembly

One person grasps the left crash bar inner bracket

⑽

and fixes the 2 bolts

⑾

at the bracket with a 14# sleeve

and fixes the bolt

⒄

head on the upper part of the crash bar with a 12# sleeve, and the other holds the right crash

bar. After support

⒂

, use 14# sleeve to remove nut

⑿

and 12# sleeve to remove nut

⒃

. After removing bolts

⑾

and

⒄

, remove the inner support of the guard bar and place it.

Содержание ZT125-GK


















































































Результаты поиска

Содержание ZT125-GK

Отзывы:

Похожие инструкции для ZT125-GK

Бренды по названию

Популярные бренды

Zontes ZT125-GK, Руководство по обслуживанию

Результаты поиска

Содержание ZT125-GK

Отзывы:

Похожие инструкции для ZT125-GK

Бренды по названию

Популярные бренды