Zodiac AquaLink M8, Руководство по установке

Страница: 19 / 44

Page 19
AquaLink
®
M8 | Installation Manual
Page 18
AquaLink
®
M8 | Installation Manual
W2
W1
4 3 2 1
W2
W1
First Control Panel
Third Control Panel
W2
W1
Second Control Panel
W2
W1
Fourth Control Panel
W2
W1
Back of
OneTouch
PCB
Jumper Location
Figure 27. Jumper Settings for Multiple OneTouch
TM
Control Panels
Section 4. System Startup
4.1 OneTouch Programming
4.1.1 Basic Programming
To set a particular piece of equipment to turn on and
off at predetermined times, highlight MENU/HELP and
press SELECT (see Figure 28). Highlight PROGRAM
and press SELECT. Use the UP or DOWN buttons to
highlight the equipment (for example, filter pump) then
press SELECT. Follow the on-screen prompts. Use the
UP or DOWN buttons to pick each number, starting
with ON hours, press SELECT to enter and move on to
the next item to change, including picking what day(s)
the program will run. If you make a mistake, use the
BACK button to return to a number. If the program is
already entered, highlight CHANGE PROGRAM and
step through to the entry that should be corrected.
A VARIABLE SPEED PUMP can be programmed
to run at any one of its eight (8) speeds. Power to the
variable speed pump is switched on/off by a relay, so to
program the pump you need to set a program time for
the relay and for any speeds that you wish to run during
the pumps on cycle.
In the example shown below, the variable speed
pump is used for pool filtration, so it will be powered
from the FILTER PUMP relay. Therefore to program the
variable speed pump you must first set a program time
for the FILTER PUMP relay, then you need to program
the desired pump speeds to turn on/off during the
FILTER PUMP cycle. If you do not program any speeds
to run during the filtration cycle, then by default the
variable speed pump will run at the POOL speed setting
during its filtration cycle.
Example:
1. The total length of the filtration cycle is to be from
8am to 5pm. So program the FILTER PUMP to
turn on at 8am and to turn off at 5pm
2. To run the variable speed pump at the SPEED3
setting from 8am to 1pm, highlight and select VSP
SPD1 PGM, then highlight and select SPEED3,
program it to turn on at 8am and off at 1pm.
3. To run the variable speed pump at the SPEED4
setting from 1pm to 5pm, highlight and VSP SPD1
PGM, then highlight and select SPEED4, program
it to turn on at 1pm and off at 5pm.
ON OFF DESCRIPTION
FILTER PUMP 8AM 5PM Total duration of
filtration cycle
SPEED3 8AM 1PM Pump runs at the
SPEED3 setting
SPEED4 1PM 5PM Pump runs at the
SPEED4 setting
NOTE The following items can be found either in the
MENU/HELP or in a Sub Menu under SYSTEM
SETUP.
4.1.2 Set the Time Menu
MENU/HELP > SET TIME
To set the time, highlight the MENU/HELP and press
SELECT. Highlight SET TIME and press SELECT.
Use the UP or DOWN button to set the values. Press
SELECT to continue.
4.1.3 Set the Temperature
1. Pool/Spa Combination
MENU/HELP > SET TEMP > POOL or SPA > SET TEMP VALUE
Highlight MENU/HELP and press SELECT. Highlight
SET TEMP and press SELECT. Use the UP or DOWN
button to highlight either POOL or SPA and press
SELECT. Use the UP or DOWN button to increase or
decrease the temperature and press SELECT. Use the
BACK button to return to the main screen.
2. Pool/Spa Only
MENU/HELP > SET TEMP > TEMP1 > SET TEMP1 VALUE >
TEMP2 > SET TEMP2 VALUE
Highlight MENU/HELP and press SELECT. Highlight
SET TEMP and press SELECT (TEMP1 must be
higher than TEMP2). Press SELECT on TEMP1. Use
the UP or DOWN button to increase or decrease the
temperature and press SELECT.
Highlight TEMP2 and press SELECT (TEMP1 must be
higher than TEMP2). Use the UP or DOWN button to
increase or decrease the temperature and press SELECT.
Use the BACK button to return to the main screen.
3. Maintain Temperature