ZCS AZZURRO 1PH HYD3000-ZP1 Скачать руководство пользователя

Страница: 167 / 195

User’s Manual 1PH HYD3000-HYD6000-ZP1

Rev. 1.0 01/09/2023

Identification: MD-AL-GI-00

Rev. 1.1 of 27/01/2023 - Application: GID

166/193

15.4.

Datalogger
15.4.1.

Preliminary notes on how to configure the datalogger

The AzzurroZCS inverters can be monitored via a datalogger connected to a Wi-Fi network present at the

place of installation or via an ethernet cable connected to a modem.

ZCS monitoring

Product code

Product photo

APP

monitoring

Portal

monitoring

Possibility to send commands and

to update the inverter remotely in

case of technical support

ZSM-WIFI

ZSM-ETH

ZSM-4G

Datalogger 4-

10 Inverters

Datalogger

up to 31

Inverters

The inverters are connected in a daisy chain to the datalogger via a RS485 serial line.

•

Datalogger up to 4 inverters (code ZSM-DATALOG-04): allows to monitor up to 4 inverters.

It can be connected to the network via an Ethernet or Wi-Fi network.

•

Datalogger up to 10 inverters (code ZSM-DATALOG-10): allows to monitor up to 10 inverters.

It can be connected to the network via an Ethernet or Wi-Fi network.

Содержание AZZURRO 1PH HYD3000-ZP1




































































































































































































Результаты поиска

Содержание AZZURRO 1PH HYD3000-ZP1

Отзывы:

Похожие инструкции для AZZURRO 1PH HYD3000-ZP1

Бренды по названию

Популярные бренды

ZCS AZZURRO 1PH HYD3000-ZP1, Руководство пользователя

Результаты поиска

Содержание AZZURRO 1PH HYD3000-ZP1

Отзывы:

Похожие инструкции для AZZURRO 1PH HYD3000-ZP1

Бренды по названию

Популярные бренды