YOKOGAWA AQ1210D Скачать руководство пользователя страница 274

Страница: 274 / 290

11-4

IM AQ1210-01EN

Code

Message

700

Failed to open the file.

701

Failed to close the file.

702

Failed to read the file.

703

Irregular file format.

704

Failed to write the file.

705

Cannot be saved. No trace data.

708

Cannot be saved. This data is not taken with this instrument.

710

File cannot be retrieved. Invalid wavelength

711

File cannot be retrieved. Invalid distance range

712

File cannot be retrieved. Invalid pulse width

713

File cannot be retrieved. Invalid sampling points

714

File cannot be retrieved. Distance range exceeds 400km.

715

File cannot be retrieved. Sampling intervals exceed 64m.

716

File cannot be retrieved. Actual averaging times or duration is not set.

717

Duplicate file name.

718

File is damaged. Check the file.

719

File name too long. Maximum length is 60 letters.

720

File is now being accessed. Execute after access is released.

721

Cannot load this file. Invalid file format or this firmware version is old.

722

Recall Setup File cannot load the measurement condition which sampling interval has been changed to shorter

than the standard sampling interval at Meas. Range Change function.

723

This file cannot be supported by the firmware with this product. Please update into the latest firmware to read this

file.

724

The model name of the instrument and model name in the file is different. This file cannot be read with this

instrument.

725

Can't use the following characters. \ / : ; * ? " < > | % . ,

726

This file cannot be read with this instrument. This file that tries to be loaded includes the measurement condition

that cannot be measured with this instrument.

727

This file cannot be read with this instrument. This file that tries to be loaded includes the measurement condition

that cannot be measured with this instrument. - Distance Range

728

This file cannot be read with this instrument. This file that tries to be loaded includes the measurement condition

that cannot be measured with this instrument. - Pulse Width

732

ID No. is not selected in File Name. Please include ID No. in File Name if using direct save(Select ID).

819

ROM Test Error occurred.

820

RAM Test Error occurred.

821

System File Test Error occurred.

822

Battery Test Error occurred.

823

Temperature Test Error occurred.

824

Power Supply Test Error occurred.

825

WLAN Test Error occurred.

854

In USB Storage mode, all keys are locked. Please disconnect the USB Cable.

902

Battery is low. Please power it off, and charge the battery or replace the battery. Or, please use the power supply.

903

Backup battery is low.

904

Hardware failed, and needs to be repaired. Please contact Yokogawa's representatives.

906

Battery is low. The instrument will be powered off in 10 sec.

909

The temperature inside the instrument is too high. The instrument may be damaged if used in this condition.

The instrument will be powered off in 10 sec. Please turn off power to allow instrument to cool down.

919

The operation of the battery is not confirmed normally. After stopping the measurement, turn off the power.

Please check the connection of battery.

922

Incorrect date and time setting. Set the correct date and time.

925

Please use AC adapter.

933

Setting conflict.

934

Communication not allowed during measurement

935

USB port over current error.

936

Invalid license key. Option was not installed.

937

The temperature inside the instrument is too high. The instrument may be damaged if used in this condition.

The instrument will be powered off in 10 sec. Please turn off power to allow instrument to cool down.

938

The temperature inside the instrument is too low. The instrument may be damaged if it is used in this condition.

The instrument will be powered off in 10 sec. Please turn off power until internal temperature is increased.

939

The temperature inside the instrument is too high. The instrument may be damaged if used in this condition.

The instrument will be powered off in 10 sec. Please turn off power to allow instrument to cool down.

11.2 Error Message Display

Содержание AQ1210D



































































































































































































































































































Результаты поиска

Содержание AQ1210D

Отзывы:

YOKOGAWA AQ1210D, Руководство пользователя, Страница: 274 / 290

Результаты поиска

Содержание AQ1210D

Отзывы: