13
O R I G I N A L I N S T R U C T I O N S
EN
TOOL DESCRIPTION
The straight grinder is a type of grinder which allows the material to be machined with grinder pins, wire brushes, and polishing
wheels. Due to the small size of the accessories, it is particularly suitable for work in places that cannot be reached with other
types of grinders. The correct, reliable, and safe operation of the appliance depends on its proper use, therefore:
Read this entire instructions manual before the
fi
rst use of the tool and keep it for future reference.
Caution! Produced during the sanding of certain surfaces, the resulting dust can be harmful to health or toxic.
The above remark applies, among others, to the sanding of surfaces covered with paints containing lead, certain types of wood,
certain metals (e.g. lead) and materials, therefore, e
ff
ective dust extraction, dust masks and other skin and respiratory protection
measures should be used during work. The supplier shall not be liable for any damage resulting from failure to comply with the
safety instructions and recommendations speci
fi
ed in this instructions manual.
PRODUCT ACCESSORIES
The product is supplied complete and does not require assembly. The supply battery and battery charger are not included.
TECHNICAL DATA
Parameter
Unit
Value
Catalogue No.
YT-82824
Rated voltage
[V]
18 DC
Tool chuck diameter
[mm]
6
Max.diameter of accessories
[mm]
25
Thread size of the
fi
xing nut
M15
Rated rpm
[min
-1
]
8,000 – 26000
Noise level
- sound pressure
[dB(A)]
78.0 ± 3.0
- power
[dB(A)]
89.0 ± 3.0
Vibration level
[m/s
2
]
2.47 ± 1.5
Protection rating
IPX0
Weight
[kg]
1.37
Battery type
Li-Ion
The declared noise emission value has been measured using the standard test method and can be used to compare one tool to
another. The declared noise emission value can be used in the preliminary exposure assessment.
The declared total vibration value has been measured using the standard test method and can be used to compare one tool to
another. The declared total vibration value can be used in the initial exposure assessment.
Caution! The vibration emission during tool operation may di
ff
er from the declared value, depending on the manner the tool is used.
Caution! Safety measures to protect the operator, which are based on an assessment of exposure under actual conditions of
use (including all parts of the work cycle, such as the time when the tool is switched o
ff
or idle and the activation time), must be
speci
fi
ed.
GENERAL SAFETY CONDITIONS
NOTE!
Get acquainted with all the instructions below. Failure to observe them may lead to an electric shock,
fi
re or injuries. The
notion of electric tool used in the instructions applies to all the tools which are powered with electric current, both wire tools and
wireless ones.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be properly illuminated and clean.
Disorder and poor illumination may be a cause of accidents.
Do not
work with electric tools in explosive environments, or those which contain in
fl
ammable liquids, gases or vapours.
Elec-
tric tools generate sparks, which may cause a
fi
re in case of contact with in
fl
ammable gases or vapours.
Do not allow children
and outsiders to the place of work.
A lack of concentration may result in a loss of control over the tool.
Electric safety
The plug of the power supply cable must
fi
t the mains socket. Do not modify the plug. Do not use any adapters whatso-
ever in order to adapt the plug to the socket.
Unmodi
fi
ed plug which
fi
ts the socket reduces the risk of an electric shock.
Avoid
Содержание YT-82824
