YASKAWA VIPA System SLIO Скачать руководство пользователя страница 304

Страница: 304 / 380

Save and transfer your project to the CPU.

After transmission, the NTP time is requested by each configured time server

and the best response for the time synchronization is used.

Please note that although the time zone is evaluated, an automatic

changeover from winter to summer time is not supported. Industrial sys-

tems with time-of-day synchronization should always be set in accord-

ance to the winter time.

With the FC 61 you can determine the local time in the CPU. More infor-

mation about the usage of this block may be found in the manual

"SPEED7 Operation List" from VIPA.

13.5 TIA Portal - Hardware configuration - I/O modules

Starting with slot 1 place in the

Device overview

of the PROFINET IO device

‘VIPA SLIO

CPU’

your System SLIO modules in the plugged sequence. For this drag from the hard-

ware catalog the corresponding module to the corresponding position in the

Device over-

view

To provide specific addressing of the installed peripheral modules, certain addresses

must be allocated in the CPU. For parameterization click in the

Device overview

at the

module you want to parameterize. Then the parameters of the module are shown in the

Properties

dialog. Here you can make your parameter settings.

Hardware configuration of

the modules

Parameterization

VIPA System SLIO

Configuration with TIA Portal

TIA Portal - Hardware configuration - I/O modules

HB300 | CPU | 013-CCF0R00 | en | 19-30

304

Содержание VIPA System SLIO





























































































































































































































































































































































































Результаты поиска

Содержание VIPA System SLIO

Отзывы:

Бренды по названию

Популярные бренды

YASKAWA VIPA System SLIO, Руководство пользователя

Результаты поиска

Содержание VIPA System SLIO

Отзывы:

Бренды по названию

Популярные бренды