YASKAWA VIPA System SLIO Скачать руководство пользователя страница 249

Страница: 249 / 380

10.9 PROFINET diagnostics

10.9.1

Overview

There are the following possibilities to get diagnostics information from your system:

Diagnostics with the configuration and engineering tool

Diagnostics during runtime in the user program (OB 1, SFB 52)

Diagnostics via OB start information

Diagnostics status indication via SSLs

10.9.2

Diagnostics with the configuration and engineering tool

If you are connected from your configuration respectively engineering tool via Ethernet

with the PROFINET IO controller, online diagnostics information may be accessed.

E.g. with

‘Station

Open online’

you get information about the state of your system.

Here missing respectively faulty components are shown by symbols.

In the following figure e.g. there is shown that the configured device 3 is missing and

device 4 reports an error.

VIPA System SLIO

Deployment PG/OP communication - PROFINET

PROFINET diagnostics > Diagnostics with the configuration and engineering tool

HB300 | CPU | 013-CCF0R00 | en | 19-30

249

Содержание VIPA System SLIO





























































































































































































































































































































































































Результаты поиска

Содержание VIPA System SLIO

Отзывы:

Бренды по названию

Популярные бренды

YASKAWA VIPA System SLIO, Руководство пользователя

Результаты поиска

Содержание VIPA System SLIO

Отзывы:

Бренды по названию

Популярные бренды