YASKAWA VIPA System SLIO Скачать руководство пользователя страница 244

Страница: 244 / 380

Starting position

IO controller is in STOP, I-Device in RUN

Event

IO controller starts

Reaction

The OB 83 (Return-of-Submodule) for input sub modules of the transfer

areas to the higher-level IO controller is called in the I-Device.

An OB 85 is called for each transfer area, which is located in the process

image, in the I-device if messages of process image transfer errors are par-

ametrized and the corresponding OB 83 has not yet been called.

An OB 122 is triggered in the I-Device for each peripheral direct access to

an input transfer area, until the corresponding OB 83 has been called.

The OB 100 (startup) is called in the IO controller.

VIPA System SLIO

Deployment PG/OP communication - PROFINET

Deployment as PROFINET I-Device > Error behavior and interrupts

HB300 | CPU | 013-CCF0R00 | en | 19-30

244

Содержание VIPA System SLIO





























































































































































































































































































































































































Результаты поиска

Содержание VIPA System SLIO

Отзывы:

Бренды по названию

Популярные бренды

YASKAWA VIPA System SLIO, Руководство пользователя

Результаты поиска

Содержание VIPA System SLIO

Отзывы:

Бренды по названию

Популярные бренды